Is cyanotype toxic? The real risk, explained
As an Amazon Associate I earn from qualifying purchases. How we fund the site
In short
- Ferricyanide’s acute toxicity is low: its oral LD50 in rats exceeds 5,110 mg/kg.
- Several safety data sheets classify it as an eye irritant and toxic to aquatic life; others don’t classify it.
- Its cyanide is bound to the iron and is released only by acids, intense heat or light on the dissolved product.
- The Prussian blue in the finished print is low hazard according to the Royal Society of Chemistry.
- New Cyanotype is a different level of risk: its oxalate is harmful if swallowed and through the skin.
On this page (8 sections)
- Low toxicity doesn’t mean “nontoxic”
- What the safety data sheets say about each reagent
- Does cyanotype contain cyanide?
- Is cyanide released when you expose the print to the sun?
- Is it dangerous to mix cyanotype with vinegar?
- What about the Prussian blue in the finished print?
- What gets passed around and what the sources say
- So is cyanotype dangerous?
Low toxicity doesn’t mean “nontoxic”#
Classic cyanotype is low in toxicity, but not harmless. The oral dose of potassium ferricyanide that kills half the test rats exceeds 5,110 mg per kilogram of body weight1, a high value. Even so, several safety data sheets classify it as an eye irritant and toxic to aquatic life2.
If you’ve arrived without knowing what cyanotype is, this is all you need: it uses two reagents, potassium ferricyanide and ferric ammonium citrate. With light, the iron in the citrate changes state and reacts with the ferricyanide to form Prussian blue, the image pigment3. Questions about toxicity concern those two powders, their solution and the final pigment; the rules for working with them are in the cyanotype safety guide.
The figure above is an LD50, or median lethal dose: the amount of product per kilogram of body weight that kills half the animals in a test. The higher it is, the lower the acute toxicity, the kind caused by a single significant exposure1. These are the values the safety data sheets give:
| Chemical | Acute toxicity according to the safety data sheets | Source |
|---|---|---|
| Potassium ferricyanide | Oral LD50 in rats above 5,110 mg/kg; dermal LD50 in rats above 2,000 mg/kg | 1,4 |
| Potassium ferricyanide | Oral LD50 in mice of 2,970 mg/kg, a different species and a different test | 5,6 |
| Ferric ammonium citrate | Oral LD50 in rats above 2,000 mg/kg | 7 |
| Ferric ammonium oxalate (New Cyanotype) | Harmful if swallowed and in contact with skin (H302 + H312) | 8 |
Low acute toxicity doesn’t mean you can swallow or touch it carelessly. Mike Ware, creator of New Cyanotype, writes in the general disclaimer on his website that some of the products in his processes are moderately toxic and that all should be considered potentially harmful9. And acute toxicity isn’t everything: eyes, skin and water each have their own section in the safety data sheets.
What the safety data sheets say about each reagent#
The ferricyanide safety data sheets disagree: Honeywell and Thermo Fisher classify it as an eye irritant and toxic to aquatic organisms2,5, and Carl Roth and PanReac don’t classify it10,6. The same goes for citrate. In practice, the most cautious version wins.
A safety data sheet (SDS) is the document in which the manufacturer states the product’s hazards. Each hazard has a code: H319 means “causes serious eye irritation,” and H411, “toxic to aquatic life with long-lasting effects”1. EUH032 is a supplementary statement under European regulations: “contact with acids liberates very toxic gas”2.
| Ferricyanide sheet | Frame | Classification | Source |
|---|---|---|---|
| Honeywell, 2025 | European CLP regulation | H319, H411 and EUH032 | 2 |
| Thermo Fisher, 2025 | European CLP regulation | H319, H411 and EUH032 | 5 |
| Sigma-Aldrich and Merck, 2026 | US standard | H319, H411 and the acid warning | 1,4 |
| Carl Roth, 2020 | European CLP regulation | Not classified; only EUH032 | 10 |
| PanReac, 2025 | UK version | Not classified | 6 |
| Jacquard, 2018 | US standard | “Not hazardous,” with the acid warning | 11 |
| International card ICSC 1132, 2002 | International Programme on Chemical Safety | Slightly irritating to eyes, skin and respiratory tract | 12 |
The difference isn’t in the data but in each manufacturer’s judgment. Carl Roth publishes the same algae toxicity value as Honeywell10,2 and, even so, doesn’t classify the product as hazardous to the aquatic environment. That’s why we take the most cautious set as our baseline: it irritates the eyes, isn’t mixed with acids and doesn’t go into the water.
With ferric ammonium citrate, the range is similar. Thermo Fisher doesn’t classify it as hazardous13, and Sigma-Aldrich’s product page shows no pictograms or hazard statements14. Jacquard’s, the brand of the kit we link to, lists it as a skin irritant (H315), eye irritant (H319) and possible respiratory irritant (H335)7. The CAMEO database from NOAA, the US oceanic and atmospheric agency, adds that its dust irritates the nose, throat and eyes15. With prolonged contact, it also causes mild skin irritation15. The details of each label are in potassium ferricyanide hazards.
Does cyanotype contain cyanide?#
Cyanotype contains cyanide groups, but not free cyanide. In potassium ferricyanide they are bound to iron in a stable complex, and the ATSDR considers these complexes much less toxic than hydrogen cyanide or sodium and potassium cyanide16. The risk arises if that complex breaks down.
The ATSDR is the US agency that assesses the health effects of toxic substances. One of the safety data sheets, Thermo Fisher’s, adds that the ferricyanide complex doesn’t break down into cyanide if swallowed5; it is the only one that says so explicitly, so we don’t take it as grounds for relaxing any precaution.
The stability of the complex shows in a lab detail. The EPA, the US environmental agency, has an official method for measuring all the cyanide in a sample, including that in iron complexes. To release it, the sample is boiled for an hour with a strong acid and a catalyst17. The conditions in which it does break down are specific, and each one has its own rule in the studio:
| Condition | What the sources say | What to do in the studio |
|---|---|---|
| Acids | Contact with acids liberates very toxic gases (EUH032)2; educational sources specify that this means strong acids18 | No acid in the powders or the solution; acids stored separately |
| Heat and fire | Above 300 °C it decomposes, giving off hydrogen cyanide, nitrogen oxides and carbon monoxide10 | Don’t heat the powders or the solution; no flames nearby |
| Light on the product dissolved in water | In natural waters, light can release free cyanide from ferricyanides16 | Leftovers and the first bath don’t go into rivers, the garden or the sea |
Is cyanide released when you expose the print to the sun?#
We haven’t found any source that measures whether a cyanotype exposure gives off cyanide, one way or the other, so we don’t claim either. What is documented is that light can release cyanide from ferricyanides dissolved in water, especially in clear water16.
That effect has been measured outside the studio. In a field study of drainage water from a mine, environmentally significant concentrations of free cyanide formed within minutes at midday19. That’s a very different situation from a coated sheet on a table. But it explains why cyanotype leftovers shouldn’t end up in a river or the garden, and why it’s worth knowing how to dispose of cyanotype waste.
In the print, the chemistry describes a different reaction: light reduces the iron in the citrate, and that iron reacts with the ferricyanide to form Prussian blue20. The safety data sheets, for their part, mention light only to say the product should be stored protected from it, because it degrades it10,5. Given that information, the sensible thing is to expose outdoors or in a ventilated room and not leave trays of solution in the sun.
Is it dangerous to mix cyanotype with vinegar?#
The safety data sheets warn about acids without naming vinegar2, and we haven’t found any source that says a dilute vinegar bath is dangerous or that it carries no risk at all. The cautious approach is the usual rule: acid goes only into the bath water, never into the powders or the solution.
Educational sources place the risk with strong acids: the Royal Society of Chemistry warns that ferricyanide can release hydrogen cyanide in contact with them18. Science in School, for its part, recommends not having strong acids in the room while working with ferricyanide21. Mike Ware, on the other hand, uses very dilute acid baths to develop New Cyanotype, such as nitric acid at around 1% or citric acid at 1–2%22.
Another official EPA method points the same way: when a sample is acidified with dilute hydrochloric acid, the cyanide in ferricyanide isn’t recovered, with a yield of 0.0%23. It’s a lab test: it supports the nuance, but it doesn’t prove zero risk. What vinegar does in the wash and whether it’s worth it is explained in vinegar in cyanotype.
If you use vinegar, check the acidity on its label. According to PanReac’s safety data sheet, acetic acid irritates the skin and eyes from 10% and is corrosive from 25%24: a vinegar under 10% is below those limits.
What about the Prussian blue in the finished print?#
Prussian blue, the pigment left in the washed print, is low hazard according to the Royal Society of Chemistry18. In this pigment the cyanide is held so tightly that the FDA, the US Food and Drug Administration, approved one of its forms, called “insoluble,” in 2003 as an oral drug to treat contamination with radioactive cesium or thallium25,26. The print contains another form, called “soluble,” although both are very poorly soluble in water22.
That drug is called Radiogardase, and its prescribing information explains that this Prussian blue isn’t absorbed through the intact intestinal wall26. Being a drug doesn’t mean a print can be sucked on or eaten: the fact only explains why the cyanide in the pigment isn’t free. A dry cyanotype, moreover, doesn’t stain your hands when you touch it20.
What we haven’t found is data on residues in garments or objects that end up in the mouth, such as bibs, teethers or tableware. Until there is, we don’t suggest cyanotype for those uses.
What gets passed around and what the sources say#
Some claims about cyanotype toxicity keep getting repeated even though they don’t hold up against the safety data sheets. These are the most common, with what the sources say:
| What you’ll hear | What the sources say | Source |
|---|---|---|
| “Cyanotype isn’t toxic” | Several safety data sheets classify ferricyanide as an eye irritant and toxic to aquatic life, and Jacquard lists citrate as a skin, eye and respiratory irritant | 2,7 |
| “It’s simply safe for kids” | Jacquard, which describes it as “nontoxic” in its FAQ, still recommends not swallowing, inhaling or touching the chemicals or the fabric, and adult supervision | 27 |
| “Ferricyanide is cyanide” | Its cyanide groups are bound to the iron, and these complexes are much less toxic than soluble cyanides | 16 |
| “Cyanide is released in the sun” | We haven’t found measurements for cyanotype; release by light is documented for the product dissolved in water | 16 |
| “Vinegar with ferricyanide is deadly” | Educational sources place the risk with strong acids, and Ware develops in very dilute acid baths | 18,22 |
| “The wash water is biodegradable” | The safety data sheets say the product must not enter the sewer system, and the ATSDR states that ferrocyanide is not readily biodegradable | 1,16 |
There are more misconceptions about the technique, not all of them about safety, in cyanotype myths.
So is cyanotype dangerous?#
Classic cyanotype is as dangerous as any product that irritates the eyes and harms water2: not very, if you work with safety glasses and gloves, away from acids and heat, and keep the leftovers out of the drain. Variants with other reagents are another matter and are covered separately.
In practice, these are the precautions that follow from the safety data sheets, and they all fit on a studio table:
- Safety glasses and nitrile gloves when weighing, dissolving, brushing and during the first wash, as precautionary statement P280 in the safety data sheets calls for2.
- No acid in the powders or the solution, and no heating them10.
- No eating, drinking or smoking while you work, as the international chemical safety card says12.
- Leftover solution and the first wash bath in a container for the hazardous waste collection point, because the safety data sheets say they must not enter the sewer system5.
How to do each of these, step by step, is in how to handle and store the reagents.
New Cyanotype, the variant Mike Ware introduced in 199528, is a different level of risk. Its ferric ammonium oxalate is classified as harmful if swallowed and in contact with skin8. Ware himself warns that his sensitizer is toxic if swallowed, more so than that of traditional cyanotype22. Its original formula also contains ammonium dichromate, which the European REACH regulation lists among substances that are carcinogenic, mutagenic and toxic to reproduction29. We explain it in safety for toning and other formulas.
Frequently asked questions
Is it dangerous to touch a finished cyanotype?
Not according to the sources we consulted. After washing, what’s left on the paper is Prussian blue, which the Royal Society of Chemistry considers low hazard, and a dry print doesn’t stain your hands. What we haven’t found is data on objects that go in the mouth, so we don’t suggest it for bibs, teethers or tableware.
Does cyanotype give off gases or fumes?
Only under conditions you avoid in the studio: in contact with acids, ferricyanide releases very toxic gases, and above 300 °C it decomposes and gives off hydrogen cyanide. In normal work, what the safety data sheets list for the respiratory tract is reagent dust, which irritates the nose and throat.
Can I do cyanotype without gloves?
You can, but it isn’t a good idea. Jacquard’s safety data sheet classifies ferric ammonium citrate as a skin irritant, and the CAMEO database describes mild irritation with prolonged contact. Wearing nitrile gloves when mixing, brushing and during the first wash avoids the problem so you don’t have to think about it.
Is New Cyanotype more toxic than classic cyanotype?
Yes, according to its own creator: Mike Ware warns that his sensitizer is toxic if swallowed, more so than that of traditional cyanotype. Its ferric ammonium oxalate is classified as harmful if swallowed and in contact with skin, and the original formula contains ammonium dichromate, which the REACH regulation lists among carcinogenic substances.
What happens if vinegar accidentally gets into the solution?
We haven’t found any source that measures that risk. The safety data sheets warn that ferricyanide releases very toxic gases with acids, and educational sources place that risk with strong acids. If it happens, don’t heat the mixture, ventilate, keep it as waste for the hazardous waste collection point and go back to the rule: acid goes only into the bath water.
Your next step
Sources
- Sigma-Aldrich. (2026). Ficha de datos de seguridad: Hexacianoferrato(III) de potasio (version 11.0, ref. 244023). https://www.sigmaaldrich.com/ES/es/sds/sigald/244023. Accessed October 16, 2026. 123456
- Honeywell Specialty Chemicals Seelze GmbH. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (version 2.4, ref. 31253). https://pdf.dutscher.com/doc/31253-1KG-HON/31253-1KG-HON_FDSen.pdf. Accessed October 16, 2026. 12345678910
- Stulik, D. C. and Kaplan, A. (2013). Cyanotype. In The atlas of analytical signatures of photographic processes. Getty Conservation Institute. https://www.getty.edu/conservation/publications_resources/pdf_publications/pdf/atlas_cyanotype.pdf
- Merck. (2026). Ficha de datos de seguridad: Potasio hexacianoferrato(III) p.a. EMSURE (version 9.1, ref. 1.04973). https://www.sigmaaldrich.com/ES/es/sds/mm/1.04973. Accessed October 16, 2026. 12
- Thermo Fisher (Kandel) GmbH. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (revision 5, ref. A16946). https://deca.upc.edu/en/laboratories/latem/security/reactius-quimics/potassium-hexacyanoferrate-iii-fisher-scientific.pdf. Accessed October 16, 2026. 123456
- Panreac Química S.L.U. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (version 8.03, art. 1503). https://shop.lgsbv.com/H365/DWN/sds_131503_en.pdf. Accessed October 16, 2026. 123
- Rupert, Gibbon & Spider, Inc. (2018). Safety data sheet: Ferric ammonium citrate (CHM1102, CHM2102, JCY1100). https://uwaterloo.ca/fine-arts/sites/default/files/uploads/documents/ferric-ammonium-citrate_2018-02-07.pdf. Accessed October 16, 2026. 123
- Thermo Fisher Scientific. (2025). Safety data sheet: Ammonium iron(III) oxalate trihydrate, 98% (revision 4, ref. 11449377). https://www.fishersci.ie/store/msds?partNumber=11449377&productDescription%3DAMMONIUM+IRON%28III%29+OXALATETRIHYDRATE%2C+98%25%2C100G&countryCode=IE&language=en. Accessed October 16, 2026. 12
- Ware, M. (n.d.). Warning & disclaimer. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/warning.html Accessed October 16, 2026.
- Carl Roth GmbH + Co. KG. (2020). Safety data sheet: Kaliumhexacyanoferrat(III) (version 3.0, art. 7971) [in German]. https://www.gm.th-koeln.de/~werkst/sicherheit/sicherheitsdatenblatt/kaliumhexacyanoferrat_III_2020_06_15.pdf. Accessed October 16, 2026. 123456
- Rupert, Gibbon & Spider, Inc. (2018). Safety data sheet: Potassium ferricyanide (CHM0101, CHM1101, CHM2101, JCY1100). https://uwaterloo.ca/fine-arts/sites/default/files/uploads/documents/potassium-ferricyanide_2018-02-28.pdf. Accessed October 16, 2026.
- International Programme on Chemical Safety (IPCS) and European Commission. (2002). ICSC 1132: Potassium ferricyanide [International Chemical Safety Card]. https://www.inchem.org/documents/icsc/icsc/eics1132.htm Accessed October 16, 2026. 12
- Thermo Fisher Scientific. (2025). Safety data sheet: Ammonium iron(III) citrate (revision 6, ref. 211840000). https://www.fishersci.ie/store/msds?partNumber=10762505&productDescription%3D250GR+Ammonium+iron%28III%29+citrate%2C+16.5+to+18.5%25+Fe&countryCode=IE&language=en. Accessed October 16, 2026.
- Sigma-Aldrich. (n.d.). Ammonium iron(III) citrate, reagent grade (ref. F5879) [Product page]. https://www.sigmaaldrich.com/IT/it/product/sigald/f5879. Accessed October 16, 2026.
- National Oceanic and Atmospheric Administration. (n.d.). Ferric ammonium citrate. CAMEO Chemicals. https://cameochemicals.noaa.gov/chemical/3462 Accessed October 16, 2026. 12
- Agency for Toxic Substances and Disease Registry. (n.d.). Toxicological profile for cyanide: Chapter 5. Potential for human exposure [Draft for public comment]. U.S. Department of Health and Human Services. https://www.atsdr.cdc.gov/ToxProfiles/tp8-c5.pdf Accessed October 16, 2026. 123456
- U.S. Environmental Protection Agency. (2004). Method 9010C: Total and amenable cyanide: Distillation (revision 3). https://www.epa.gov/sites/default/files/2015-12/documents/9010c.pdf Accessed October 16, 2026.
- Royal Society of Chemistry. (n.d.). The blueprint reaction. Education in Chemistry. https://edu.rsc.org/exhibition-chemistry/the-blueprint-reaction/3010606.article Accessed October 16, 2026. 1234
- Johnson, C. A., Leinz, R. W., Grimes, D. J. and Rye, R. O. (2002). Photochemical changes in cyanide speciation in drainage from a precious metal ore heap. Environmental Science & Technology, 36(5), 840–845. https://doi.org/10.1021/es011064s
- Sentoku, S., Kurashina, M. and Kida, K. (2025). Observation of blue particles formed by photosensitizing reaction on paper fibres of cyanotypes. Photochem, 5(3), Article 18. https://doi.org/10.3390/photochem5030018 12
- Egan, P. (2025, June 10). Adventures in cyanoprinting: Where art and chemistry meet. Science in School, 73. https://scienceinschool.org/article/2025/cyanoprinting-where-art-and-chemistry-meet/
- Ware, M. (n.d.). The New Cyanotype process. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/New_Cyanotype_Process.html Accessed October 16, 2026. 1234
- U.S. Environmental Protection Agency. (2010). Method OIA-1677-09: Available cyanide by ligand exchange and flow injection analysis (FIA). https://19january2017snapshot.epa.gov/sites/production/files/2015-08/documents/method_oia-1677-09_2010.pdf Accessed October 16, 2026.
- Panreac Química S.L.U. (2025). Safety data sheet: Acetic acid glacial (version 10.05, art. 1008). https://deca.upc.edu/en/laboratories/latem/security/reactius-quimics/acetic-acid-panreac.pdf. Accessed October 16, 2026.
- U.S. Food and Drug Administration. (2003, October 2). FDA approves first New Drug Application for treatment of radiation contamination due to cesium or thallium [Press release]. https://www.fda.gov/drugs/bioterrorism-and-drug-preparedness/fda-approves-first-new-drug-application-treatment-radiation-contamination-due-cesium-or-thallium Accessed October 17, 2026.
- U.S. Food and Drug Administration. (2003). Radiogardase (insoluble Prussian blue) capsules: Prescribing information (NDA 21-626). https://www.accessdata.fda.gov/drugsatfda_docs/label/2003/21626_radiogardase_lbl.pdf Accessed October 16, 2026. 12
- Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026.
- Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026.
- European Commission. (2013). Commission Regulation (EU) No 348/2013 of 17 April 2013 amending Annex XIV to Regulation (EC) No 1907/2006 (REACH). https://www.legislation.gov.uk/eur/2013/348/data.html Accessed October 16, 2026.
Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.
How to cite this page
The Cyano Codex. (2026, October 16). Is cyanotype toxic? The real risk, explained. https://cyanocodex.com/en/safety/is-cyanotype-toxic/