Skip to content
The Cyano Codex
Choose language

Common cyanotype problems and how to fix them

Almost every cyanotype problem has a cause you can check: too little or too much light, a poorly judged wash, something alkaline, an uneven coating or paper that fogged before exposure. This page sorts the symptoms, explains what causes them according to the sources and points you to the fix for each one.
Reviewed
Reading time
13 min
Sources
15

As an Amazon Associate I earn from qualifying purchases. How we are funded

A pile of uneven cyanotype tests set aside and, in front, a good print of a fern
Plate 1Failed tests teach you something too.

In short

  • The most likely cause of a pale print is a short exposure; when in doubt, overexpose.
  • Overwashing also lightens the image, because the water carries off some of the blue.
  • If the whites come out greenish yellow right after washing, the wash was too short.
  • Anything alkaline, from phosphate detergent to board with an alkaline buffer, damages the blue for good.
  • Coated paper that turns green or blue before exposure will give fogged whites.
  • Gray or bronze shadows when you take the print out of the light aren’t a flaw: they mean exposure is complete.
On this page (14 sections)
  1. Why does a cyanotype go wrong?
  2. Symptoms, causes and fixes at a glance
  3. Pale prints, or prints that lighten in the water
  4. Yellow or greenish whites
  5. Bluish whites: fogging
  6. Spots and marks on the print
  7. Streaks and uneven coating
  8. Soft or unsharp images
  9. Gray or bronze shadows during exposure
  10. When nothing’s wrong, but you want more blue
  11. Five checks before you blame the chemistry
  12. Which damage can be fixed and which can’t?
  13. What gets passed around without a source
  14. Safety when correcting a print

Why does a cyanotype go wrong?#

The sources document five reasons a cyanotype goes wrong. The light wasn’t right, the wash was too short or too long, something alkaline touched the print, the coating came out uneven or the paper spoiled before exposure. Each cause leaves a different mark.

Many of those marks show up before you’re done. Coated paper should dry lemon yellow: if it turns green or blue, the whites will come out fogged1. During exposure, gray or bronze shadows mean there has been enough light2,1. And in the wash, the greenish-yellow tint clearing from the whites tells you when to stop2.

Learn more: what to buy for cyanotype, because a good share of the failures come from the paper or the chemistry, not from technique.

Diagram 1 places each problem at the point in the process where it starts. If you’d rather go straight to your case, troubleshoot your print step by step: a few questions about what you see lead you to the most likely cause, with its sources.

Where each cyanotype problem startsSix stages in a row: coating, drying in the dark, exposing, washing, drying and storing, with the problems that start at each one. Coating: streaks from an uneven coat; with New Cyanotype, puddles that crystallize; stains from touching with damp hands. Drying in the dark: the paper should stay lemon yellow, and if it turns green or blue it is fogged; paper stored too long. Exposing: with too little light, a pale print; with poor contact, little detail; with too much light, a dark, clogged print; gray or bronze shadows mean full exposure and are not a fault. Washing: a short wash leaves greenish-yellow whites; a long wash or hard water lightens the print. Drying: the blue darkens as it oxidizes in the air, and that’s normal. Storing: light fades it, and it recovers in the dark; alkalis turn it yellow and it doesn’t recover. Normal effects, which are not faults, are marked separately.Coatstreaks from anuneven coatpuddles thatcrystallize, with NewCyanotypestains from damphandsDry in the darkshould stay lemonyellow; green or blue =fogpaper storedtoo longExposetoo little light =pale printpoor contact =little detailtoo much light =dark, clogged printgray or bronzeshadows = fullexposure (normal)Washshort wash =greenish-yellowwhiteslong wash or hardwater = printlightensDrythe blue darkens asit oxidizes in air(normal)Storelight = fades;recovers in the darkalkalis = yellows;doesn’t recoverproblem that starts at that stagein cyan: normal effect, not a fault Where each cyanotype problem starts1Coatstreaks from an uneven coatpuddles that crystallize, with New Cyanotypestains from damp hands2Dry in the darkshould stay lemon yellow; green or blue = fogpaper stored too long3Exposetoo little light = pale printpoor contact = little detailtoo much light = dark, clogged printgray or bronze shadows = full exposure(normal)4Washshort wash = greenish-yellow whiteslong wash or hard water = print lightens5Drythe blue darkens as it oxidizes in air (normal)6Storelight = fades; recovers in the darkalkalis = yellows; doesn’t recoverproblem that starts at that stagein cyan: normal effect, not a fault
Diagram 1The stage of the process where each problem starts. Each problem has its stage of origin; those marked as normal are not faults.

Symptoms, causes and fixes at a glance#

For each symptom, the table sums up the cause the sources give as most likely, how to check it and what to do. Find the row for your case and follow the link to its section, further down.

Symptoms, causes and fixes
Symptom Most likely cause How to check What to do
Pale print Exposure too short3 It had barely changed color when you took it out of the light Lengthen the exposure and make a test strip
Lightens when washed Long wash, hard or alkaline water, or the loss inherent to the classic formula1 It had good contrast before it went in the water Wash only as long as needed, avoid hard water and overexpose
Greenish-yellow whites Insufficient washing2 The tint is there right after washing Wash until it’s completely gone
Yellows over time Contact with something alkaline4 It appears days or months later Remove the cause; the damage doesn’t recover
Bluish whites Paper or solution fogged before exposure1 The coated paper was green or blue Discard it and try another paper
Irregular spots Damp hands, sweat or skin oils3 Finger-shaped marks Dry hands or gloves
Streaks Uneven coating or too much solution1 They follow the direction of the brush Less solution and, if needed, a wetting agent
Little detail The negative or object wasn’t pressed against the paper3 Soft edges where something lifted Heavy glass or a contact printing frame
Gray or bronze shadows Full exposure: not a flaw3 Visible before washing Wash and let dry
Very dark and blocked up Overexposure3 Visible after washing and drying Reduce the time
Blue dulls over the months Light4 It has been hanging in the light A few days in the dark, with air

Pale prints, or prints that lighten in the water#

A print comes out pale mainly when it didn’t get enough light: the manufacturer Jacquard gives this as the most likely cause and advises overexposing when in doubt3. If the image looked good and then lightened in the water, look at the wash: overwashing carries off some of the blue2.

With the classic formula, it’s also normal for a large part of the blue to disperse into the development water, and the traditional answer has been to overexpose heavily1. Hard or alkaline water makes the loss worse1. Conservators cited by Ware measured about 18% less density in cyanotypes washed for 15 minutes in tap water4.

Learn more: why my cyanotype comes out light, with each cause, how to check it and how to correct it.

Yellow or greenish whites#

If the whites are yellowish or greenish right after washing, the most likely reason is that the wash was too short. Keep going until the greenish-yellow tint of the unexposed iron salts has completely gone2. If the yellowing appears days or months later, the cause is something else.

That late yellowing is the trace of something alkaline. Prussian blue holds up well in neutral or acidic conditions, but alkaline materials break it down quickly5, and Jacquard blames discoloration to brown or yellow on phosphates, soap or dirty objects3. Unlike light damage, this damage doesn’t recover4. And if the print changes color as it dries, Jacquard also attributes this to incomplete washing3; the blue darkening a little as it dries, on the other hand, is normal.

Learn more: why my cyanotype comes out yellow and how to tell the two causes apart.

Bluish whites: fogging#

Fogging is blue that shouldn’t be in the white areas. Its clearest cause comes before exposure: if the coated paper has turned green or blue, its whites are already chemically fogged, and Mike Ware advises discarding it and finding a better paper1.

Coated paper also deteriorates over time, which is why Ware advises exposing it within hours of preparing it1. Over time, the coating oxidizes and the whites degrade, according to the National Science and Media Museum2. If the paper was still yellow, check the wash, which is the other cause backed by a source.

Learn more: fogging in cyanotype, with the paper color test.

Spots and marks on the print#

Spots have different causes depending on their shape. Irregular, finger-like marks usually come from touching the coated paper or the print with damp hands. Jacquard also warns that sweat and skin oils discolor the image3,6.

Jacquard also says the surface and any objects you place on it should be dry7. In Ware’s New Cyanotype, excess solution can crystallize inside the paper and draw branching marks, like fern fronds1. For white specks, there are explanations going around that we haven’t been able to confirm.

Learn more: spots in cyanotype, by shape and by stage of the process.

Streaks and uneven coating#

Streaks almost always come from an uneven coating: the solution wasn’t spread evenly or it pooled. Ware recommends not overloading the paper1 and notes that a wetting agent such as Tween 20 makes it much easier to spread the solution evenly1.

The wetting agent has one exception: it can react badly with gelatin-sized papers1. And quantity matters: with a glass rod, about 1.5 ml of solution is enough for an 8 × 10 inch (20.3 × 25.4 cm) print, and a brush uses more, up to twice as much8.

Learn more: streaks in cyanotype and how to lay down an even coat.

Soft or unsharp images#

A cyanotype comes out soft when the negative or object isn’t pressed against the sensitized surface. Jacquard stresses that the film must lie flush with the print to get detail, and suggests working on a flat surface with a heavy sheet of glass on top3.

Cyanotype is printed by contact: the negative is the same size as the final image and sits directly on the sensitized surface9. That’s why any gap shows. In the preface to her book, Anna Atkins had already noted that, with thick specimens, she couldn’t press the glass down hard enough and the impression came out imperfect in places10.

Learn more: blurry cyanotypes or cyanotypes with little detail.

Gray or bronze shadows during exposure#

Seeing gray or bronze shadows when you take the print out of the light isn’t a flaw: it’s the sign that exposure is complete. The National Science and Media Museum says to expose the classic formula until the shadows look bronzed2, and Jacquard describes its well-exposed fabric the same way3.

Those shadows regain their blue during development or, failing that, as they dry1, in about 24 hours according to Ware11. Real overexposure shows up later: a dry print that’s too dark and blocked up, which Jacquard corrects by reducing the time3.

Learn more: overexposed cyanotypes and when bronzing really is a warning.

When nothing’s wrong, but you want more blue#

If the print is fine but you want a denser blue, there are four sourced options: expose enough, apply two coats of solution, use a very dilute acid first bath and avoid hard water. Jacquard accepts a double coat for denser prints3, and Ware, with his New Cyanotype, gets stronger shadows with a very dilute acid bath1.

Hydrogen peroxide is another matter: it brings out the final blue sooner, but sources disagree on whether it intensifies it1,12.

Learn more: how to get a deeper blue and more contrast.

Five checks before you blame the chemistry#

Before you change kits or formulas, check these five things in this order. They’re the causes that come up most often in the sources and the cheapest to correct.

  1. The light. Make a test strip with bands whose times double from one to the next; the right time may fall between two13. How to read it is in cyanotype exposure time.
  2. The coated paper. It should dry lemon yellow; if it shifts to green or blue, discard it1.
  3. The paper. Ware recommends using only papers without a calcium carbonate alkaline buffer11.
  4. The water. Avoid alkaline or hard water, with calcium salts, because it degrades the image1.
  5. The wash. Wash at least until the water runs clear and the greenish-yellow tint is gone, but no longer than that3,2.

Published times vary widely: Jacquard gives 1 to 30 minutes in the sun depending on conditions, and Ware considers 30 minutes or more typical for the classic formula under a UV source3,1. They depend on the formula, the light, the paper and even humidity and heat2. If you want to go over the whole process, from solution to wash, it’s in how to make a cyanotype step by step.

Which damage can be fixed and which can’t?#

Only light damage can be fixed at home. In Mike Ware’s tests, a cyanotype faded by light recovered at least 95% of its density in the dark within a day4. Damage from an alkali, and blue carried off by water, on the other hand, don’t recover4.

Which damage can be fixed
Damage What causes it Does it recover? Source
Fading Light, especially direct sun Almost completely, in the dark and with air 4
Yellowish bleaching Any alkaline substance No 4
Loss in water Long washes and hard or alkaline water No 4

Recovery needs air: in an experiment cited by Ware, cyanotypes sealed away from oxygen stayed white and only regained their blue when they were opened4. That’s why it’s best not to seal them. What happens with sun and darkness, with the figures, is in why cyanotype fades in the sun.

What gets passed around without a source#

More causes get passed around than the ones we list here. People talk about streaks from the metal in brushes, bands from the texture of the tray bottom, white specks from bubbles, grainy prints from dry air, or edges that bleed. Some are plausible, but we haven’t been able to confirm them in reliable sources, so we don’t offer them as a diagnosis.

Christina Z. Anderson’s manual devotes an entire chapter to troubleshooting14. We haven’t consulted it, so we don’t attribute any information to it. If one of those causes fits your case, run a test changing only that variable and compare the two prints.

Safety when correcting a print#

Correcting a print adds little risk, but some remedies use products with their own data sheet. Acid baths are very dilute and never go near the chemicals, because ferricyanide’s data sheets warn that, with acids, it releases highly toxic gases15. Everything else is in cyanotype safety.

Safety: Use vinegar or citric acid only diluted in the bath water; never add them to the powders or to the classic-formula sensitizer. More on safety

In this chapter

Frequently asked questions

Can you fix a cyanotype that went wrong?

It depends on the problem. A print faded by light recovers almost all of its blue after a few days in the dark with air, and yellowish whites from underwashing can be corrected by washing more. Damage from an alkali and blue carried off by water, on the other hand, don’t recover: in those cases, the answer is to make another print.

Is it normal for the wash water to turn blue?

A little, yes, with the classic formula: Mike Ware explains that some of the Prussian blue disperses into the development water and is lost. If the water turns very blue and the print lightens a lot, check three things: whether the exposure was long enough, whether you washed longer than needed, and whether your water is hard or alkaline.

Why does my cyanotype darken as it dries?

Because the blue finishes forming with oxygen from the air: shadows that come out of the wash pale gradually regain their value as they dry, in about 24 hours according to Mike Ware. That’s normal. What isn’t normal is yellow or greenish tones appearing in the whites, which the manufacturer Jacquard attributes to incomplete washing.

Why does every cyanotype come out different with the same time?

Because exposure time depends on the formula, the ultraviolet light reaching you that day, the paper and even humidity and heat. Sources publish anything from one minute to half an hour or more, depending on conditions. When one of those variables changes, the time changes, and a test strip gives you the measure.

What if my problem isn’t listed here?

Try the step-by-step Troubleshooter, which goes from what you see on the print to the most likely cause. If that doesn’t fit either, there may be two causes at once, or one that the sources we’ve checked don’t explain. In that case we’d rather not give you an unsupported remedy: change just one variable in each test and compare.

Your next step

Troubleshoot your print step by step

Pick what you see in your cyanotype and answer a few questions: you get the most likely cause, what you can try and the sources. Free, no sign-up.

Go to the next step: Troubleshoot your print step by step

Sources

  1. Ware, M. (n.d.). The New Cyanotype process. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/New_Cyanotype_Process.html Accessed October 16, 2026. 12345678910111213141516171819
  2. National Science and Media Museum. (2011, February 18). Introduction to the cyanotype process. National Science and Media Museum Blog. https://blog.scienceandmediamuseum.org.uk/introduction-cyanotype-process/ Accessed October 17, 2026. 123456789
  3. Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer’s instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026. 123456789101112131415
  4. Ware, M. (2003). A blueprint for conserving cyanotypes. Topics in Photographic Preservation, 10, 2-18. https://resources.culturalheritage.org/pmgtopics/2003-volume-ten/10_02_Ware.pdf 12345678910
  5. Stulik, D. C. and Kaplan, A. (2013). Cyanotype. In The atlas of analytical signatures of photographic processes. Getty Conservation Institute. https://www.getty.edu/conservation/publications_resources/pdf_publications/pdf/atlas_cyanotype.pdf
  6. Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026.
  7. Jacquard Products. (2015). Cyanotype tips and troubleshooting [Manufacturer document, version 6.01.15]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Tips_and_Troubleshooting.pdf Accessed October 16, 2026.
  8. Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026.
  9. Gil-Segovia, J. A. (2022). La cianotipia como recurso en el arte contemporáneo: una luz azul que no se apaga. Arte, Individuo y Sociedad, 34(1), 167–186. https://doi.org/10.5209/aris.73063
  10. Franchi, S. (2024). Crafting and collecting cyanotypes: Anna Atkins's Photographs of British Algae: Cyanotype Impressions. Literature Compass, 21(1-3), Article e12708. https://doi.org/10.1111/lic3.12708
  11. Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026. 12
  12. Tirak, L. M. (2021). Black and blue: Revelations in Harold Mahoney's X-rayed anatomical sections. The Rijksmuseum Bulletin, 69(1), 27–49. https://doi.org/10.52476/trb.9603
  13. Ilford Photo. (2017, March 30). Making a black & white print: Exposure testing. https://www.ilfordphoto.com/exposure-testing/ Accessed October 16, 2026.
  14. Anderson, C. Z. (2019). Cyanotype: The blueprint in contemporary practice. Routledge. https://www.routledge.com/products/9781138338845
  15. Honeywell Specialty Chemicals Seelze GmbH. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (version 2.4, ref. 31253). https://pdf.dutscher.com/doc/31253-1KG-HON/31253-1KG-HON_FDSen.pdf. Accessed October 16, 2026.

Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.

How to cite this page

The Cyano Codex. (2026, October 16). Common cyanotype problems and how to fix them. https://cyanocodex.com/en/troubleshooting/