Skip to content
The Cyano Codex
Choose language

Cyanotype Sensitizer Calculator

The calculator tells you how much cyanotype mixture you need for a surface and how much citrate and ferricyanide you have to weigh out to make it. It only calculates with figures from a verified source: where there isn’t one, it says so instead of making one up. It runs in your browser and remembers your data only there.
Section
Tools
Reviewed
Sources
7
Two amber bottles marked A and B, a graduated cylinder with greenish-yellow solution and a glass rod on watercolor paper
Plate 1The two solutions, in equal parts.

Calculate your sensitizer

1What and what size

Sheets of paper or pieces of fabric of the same size.

2How you apply it
3Your chemistry

4Coats

Make extra

If you want to make a little more than the exact amount, say how much.

Each coat uses the same amount again.

What you need

We only give amounts with a verified source. Where we don’t have one yet, you’ll see “Not yet verified” instead of a figure.

In short

  • With a glass rod, Ware estimates about 1.5 ml of mixture for a 20.3 × 25.4 cm print.
  • A brush uses more: up to twice as much, according to Ware.
  • An A4 sheet coated with a rod takes about 1.8 ml of mixture: 1 ml of each solution, rounding up.
  • The grams come from Ware’s formula: 25 g of citrate and 10 g of ferricyanide, each in 100 ml.
  • For fabric, foam brushes or kit chemistry there is no verified figure yet.
On this page (7 sections)
  1. What does the Sensitizer Calculator work out?
  2. How to use the calculator, in four steps
  3. Where do the figures come from?
  4. Why do some cases say “Not yet verified”?
  5. How much mixture should you make at once?
  6. Safety when weighing and mixing
  7. The calculator’s limits

What does the Sensitizer Calculator work out?#

The Sensitizer Calculator tells you how many milliliters of cyanotype mixture you need to cover a surface and, from that, how many grams of each chemical to weigh out. It takes into account the size, the number of pieces, how you apply the mixture, the number of coats and an optional extra margin.

It only calculates with figures that have a verified source. Where there isn’t one, you’ll see “Not yet verified” instead of a figure. It is one of the site’s free cyanotype tools, and it is based on the cyanotype formula, where each amount is explained.

How to use the calculator, in four steps#

  1. Choose what you are going to coat. Paper or fabric. With fabric, the calculator only shows you the application methods that suit textiles.
  2. Enter the size and how many pieces. A4, A5, A6, Letter, 13 × 18 cm, 20 × 25 cm, 8 × 10 inches or another size, in centimeters or inches.
  3. Say how you’ll apply the mixture. Glass rod, brush or flat brush, or foam brush. If you are going to apply more than one coat, say so: each coat uses the same amount.
  4. Read the result. It appears instantly, with no button: the surface area, the total mixture, the volume of each solution and the grams of citrate and ferricyanide. Open “How we calculate it” to see each step with its source.

Where do the figures come from?#

The calculator’s figures come from two pieces of data from Mike Ware. The first tells you how much mixture is used: with a glass rod, about 1.5 ml for a 20.3 × 25.4 cm print1, and with a brush, up to twice as much2. The second is his traditional formula, which sets how much chemical goes into each solution.

The calculator converts that usage figure into milliliters per square centimeter and multiplies it by your surface area. This is our own calculation, and the result says so.

How much sensitizer each size needsFour sheets drawn to relative scale, with the amount of mixed sensitizer with a rod and with a brush: A5, 14.8 × 21 cm, 0.9 and 1.8 ml; Letter, 21.6 × 27.9 cm, 1.75 and 3.5 ml; A4, 21 × 29.7 cm, 1.8 and 3.6 ml; A3, 29.7 × 42 cm, 3.6 and 7.3 ml. Beside them, a 20.3 × 25.4 cm reference rectangle with Ware’s figure: 1.5 ml with a rod and up to twice as much with a brush. Note: our own calculation from Ware’s figure, 0.29 ml per 100 cm² with a rod; the mixture is in equal parts, so half of it is each solution; it applies to paper, not fabric.Rod / brush, in ml of mixtureA514.8 × 21 cm0.9 / 1.8 mlLetter21.6 × 27.9 cm1.75 / 3.5 mlA421 × 29.7 cm1.8 / 3.6 mlA329.7 × 42 cm3.6 / 7.3 mlWare’s figure20.3 × 25.4 cm1.5 ml with a rod; up to twice as much with a brushOur calculation from Ware’s figure (0.29 ml per 100 cm² with a rod). Equal-parts mixture: half of each solution. Applies to paper, not fabric. How much sensitizer each size needsRod / brush, in ml of mixtureA514.8 × 21 cm0.9 / 1.8 mlLetter21.6 × 27.9 cm1.75 / 3.5 mlA421 × 29.7 cm1.8 / 3.6 mlA329.7 × 42 cm3.6 / 7.3 mlWare’s figure20.3 × 25.4 cm1.5 ml with a rod; up totwice with a brushOur calculation from Ware’s figure (0.29 ml per100 cm² with a rod). Equal-parts mixture: half ofeach solution. Applies to paper, not fabric.
Diagram 1How much sensitizer each size needs. Our calculation from Ware’s figure (0.29 ml per 100 cm² with a rod). Equal-parts mixture: half of each solution. Applies to paper, not fabric.

Ware’s traditional formula uses 25 g of green ferric ammonium citrate and 10 g of potassium ferricyanide, each dissolved in distilled water to make 100 ml, and the two solutions are mixed in equal parts2. With that ratio, the calculator splits the mixture in half and converts each half into grams of chemical.

Data the tool calculates with
Figure used Value Source
Mixture with a glass rod About 1.5 ml per 20.3 × 25.4 cm Ware (2009), p. 81
Mixture with a brush or flat brush 1.5 to 3 ml per 20.3 × 25.4 cm Ware (n.d.)2
Citrate solution 25 g of green ferric ammonium citrate per 100 ml Ware (n.d.)2
Ferricyanide solution 10 g of potassium ferricyanide per 100 ml Ware (n.d.)2
Mixing ratio 1:1 Ware (n.d.)2

A worked example: an A4 sheet measures 623.7 cm², and with a rod it takes 1.81 ml of mixture according to Ware’s figure1. The calculator always rounds up, so it suggests 1 ml of each solution, that is, 0.25 g of citrate and 0.10 g of ferricyanide2. These amounts are so small that, in practice, it’s better to make more in the same ratio.

Why do some cases say “Not yet verified”?#

The calculator leaves out a figure for cases where we haven’t found a reliable source: the foam brush, fabric by brush or by immersion, and the ratio used in commercial kit chemistry. Rather than give you an unsupported estimate, it tells you the figure is missing.

Ware’s figure refers to paper and doesn’t apply to fabric. For its set, Jacquard gives a yield in prints, about 65 at 8 × 10 inches on paper and about 50 on fabric according to the manufacturer, as reproduced by a distributor3; it’s useful for getting an idea, but it doesn’t say how many milliliters each square centimeter of fabric absorbs. The sourced recipes, moreover, don’t all use the same ratio: they range from 20 to 26 g of citrate and from 9 to 10 g of ferricyanide per 100 ml4,5. That’s why the calculator works only with Ware’s.

If you are coating fabric, see cyanotype on fabric, which explains how to prepare and soak the textile.

How much mixture should you make at once?#

It’s best to make only the mixture you are going to use in the session, because it doesn’t keep long. The sources don’t agree on how long: Ware says his mixture lasts days2, and Jacquard that the one in its kit is only stable for 2 to 4 hours6.

Kept separate, the solutions last longer. Ware stores them in brown bottles in the dark2, and Jacquard gives the ones in its kit at least 6 months to 1 year7. For the mixture, however, we haven’t found a documented explanation of why the two sources disagree, so the cautious rule is the shorter one: mix at each session. What each source says, and how to store the solutions, is in how long cyanotype sensitizer lasts.

If you are mixing for a group, the “Make extra” option lets you add a margin. How to plan amounts for a whole class is covered in how to run a cyanotype workshop.

Safety when weighing and mixing#

The calculator tells you how much to weigh; safety depends on how you do it. Weigh the powders away from drafts and make the solutions wearing gloves and glasses, in containers set aside for the workshop.

Safety: Weigh the powders slowly and away from drafts so you don’t raise dust; if the kit lets you dissolve them in their own bottle, even better. More on safety

Safety: Wear safety glasses and nitrile gloves to mix and brush on the solution; if it splashes into your eyes, rinse with plenty of water for 15 minutes. More on safety

The calculator’s limits#

How to spread the mixture so you use just enough and get an even coat is explained in how to coat paper for cyanotype. And if you are starting with a kit, cyanotype kits compares what each type includes and how far it goes according to its manufacturer.

Frequently asked questions

How much cyanotype sensitizer do I need for an A4 sheet?

With a glass rod, about 1.8 ml of mixture, based on Mike Ware’s figure scaled to A4; with a brush, up to twice as much. Since the mixture is in equal parts, that’s roughly 1 ml of each solution. If you apply two coats, count double, and make a little extra if it’s your first time.

Why doesn’t the calculator give figures for fabric?

Because we haven’t found a source that says how much sensitizer fabric absorbs by area or by weight, and the Ware figure we use for paper doesn’t apply to it. Jacquard gives a yield in prints for its set, not per square centimeter. When we have a verified figure, the calculator will use it.

Does the calculator work if I use a kit?

It works for knowing how much mixture you’ll use, because that depends on the surface area and how you apply it. What it doesn’t do yet is split that mixture into grams of each chemical in the kit: each manufacturer uses its own ratio. For that, follow the kit’s instructions.

Can I make up mixed sensitizer for several days?

Better not. The sources don’t agree on how long the mixture lasts: Ware speaks of days for his formula and Jacquard of a few hours for the one in its kit. The cautious approach is to store the two solutions separately, in brown bottles in the dark, and at each session mix only what you are going to use.

Your next step

Coat the paper with the mixture you’ve calculatedHow to coat paper for cyanotype: how much sensitizer per sheet, brush or rod, wetting agent, drying in the dark and how to tell the coat came out right.

Sources

  1. Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026. 123
  2. Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026. 123456789
  3. Eckersley's Art & Craft. (n.d.). Jacquard Cyanotype Sensitizer Set [Product page]. https://www.eckersleys.com.au/products/jacquard-cyanotype-sensitizer-set Accessed October 17, 2026. (supporting source)
  4. National Science and Media Museum. (2011, February 18). Introduction to the cyanotype process. National Science and Media Museum Blog. https://blog.scienceandmediamuseum.org.uk/introduction-cyanotype-process/ Accessed October 17, 2026.
  5. Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026.
  6. Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026.
  7. Jacquard Products. (n.d.). Cyanotype [Cyanotype Kit instruction booklet]. https://jacquardproducts.com/s/Cyanotype-Kit-INSTRUCTION-BOOKLET.pdf Accessed October 17, 2026.

Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.