Skip to content
The Cyano Codex
Choose language

Cyanotype on fabric, step by step

Cyanotype on fabric is the same technique as on paper, applied to a natural-fiber textile: you coat the fabric with the iron-salt solution, dry it in the dark, expose it in the sun with plants or objects on top and rinse it in water. Here is the whole process, from new fabric to dry garment.
Reviewed
Reading time
19 min
Sources
20
Level
Beginner (level 1 of 3)

As an Amazon Associate I earn from qualifying purchases. How we are funded

Gloved hands lifting a freshly blue-dyed cotton fabric with white ferns out of the water
Plate 1The fabric turns blue in the first wash.
Time
One work session, plus drying in the dark and about 24 h until the final blue
Level
Beginner
Materials
12
Steps
7

In short

  • Natural fibers such as cotton, linen, silk or wool work; polyester, in general, doesn’t.
  • The chemistry is the same as for paper: brush it on or dip the fabric, and dry it in the dark.
  • Jacquard gives 1 to 30 minutes in the sun, with no distinction between fabric and paper: fine-tune it with a test strip.
  • Rinse for at least 5 minutes, changing the water until it runs clear; the blue matures in about 24 hours.
  • Based on the yield Jacquard states, fabric uses about 30% more solution than paper.
  • Wash the garment rarely, by hand, in cold water and without phosphates: alkalis yellow the blue and overwashing lightens it.

Safety: Coat the fabric wearing nitrile gloves and old clothes: the solution stains skin and textiles. More on safety

Safety: Wear safety glasses and nitrile gloves to mix and brush on the solution; if it splashes into your eyes, rinse with plenty of water for 15 minutes. More on safety

Safety: When exposing in the sun, protect yourself as you would for any time outdoors: shade while you wait, UV-blocking sunglasses and sunscreen; don’t look at the sun. More on safety

Materials list

Check off what you already have on the table. The “Amazon” links are affiliate links.

Learn more: the complete materials list, with what changes when the support is cloth rather than a sheet of paper.

What you need

Your check marks are saved only in this browser. No account needed.

On this page (10 sections)
  1. What is cyanotype on fabric?
  2. Choose a natural-fiber fabric
  3. Pretreated fabric, or coat it yourself?
  4. Before you start: protection and space
  5. How to make a cyanotype on fabric, step by step
    1. 1. Wash the fabric before coating it
    2. 2. Mix the solution just before use
    3. 3. Coat the fabric under dim light
    4. 4. Dry the fabric in the dark
    5. 5. Compose and expose in the sun
    6. 6. Rinse in water until it runs clear
    7. 7. Dry in the shade and wait for the final blue
  6. If something goes wrong
  7. What circulates about cyanotype on fabric
  8. Caring for the garment after the first rinse
  9. Variations: color, paint and toning
  10. Fabric projects to start with

What is cyanotype on fabric?#

Cyanotype on fabric is the classic technique applied to a natural-fiber textile. The solution of two iron salts soaks into the fibers, ultraviolet light forms Prussian blue in them, the pigment of the image, and water removes the chemistry that hasn’t reacted1.

Coating means spreading that solution over the support, and on fabric it’s done as on paper. Mike Ware says the sensitizer can also be applied to fabrics2, and Jacquard allows any natural fiber or porous surface for its set3. In cyanotype there is no layer added on top of the support: the Prussian blue particles coat the fibers of the support itself4.

That absence of a layer is the main advantage on fabric. Hande Bilvar, citing Ware, notes that iron processes are considered the best suited to delicate textiles because they need no binder such as gelatin or gum, which would alter the drape of the fabric5. The textile keeps its feel and movement.

Learn more: how cyanotype works, with the reaction explained step by step.

Choose a natural-fiber fabric#

Natural fibers work for cyanotype. Jacquard lists silk, cotton, wool, hemp, linen and canvas6, and explains that polyester, not being a natural fiber, generally doesn’t work6. For blends we haven’t found any reliable source that gives a minimum percentage of cotton: if you have one, test a scrap first.

To start, choose white or unbleached cotton. The background color matters because cyanotype is transparent, like a dye, and adds to the color of the fabric6.

Learn more: which fabric works for cyanotype, covering linen, silk, blends and colored fabrics.

Pretreated fabric, or coat it yourself?#

Pretreated fabric comes with the chemistry already dry: you take it out of the package, compose and expose. Coating it yourself means preparing the solution, but lets you choose the textile, the size and the garment. For a first test or for the classroom, pretreated fabric avoids handling the reagents; for a T-shirt or a scarf, you coat it yourself.

Jacquard makes its own in cotton sateen, in 21.6 × 27.9 cm sheets sold in packs of 10 or 30, and says to expose it for 3 to 10 minutes in the sun before rinsing7. It can be used on both sides, but the side the manufacturer specifies for the image is the shiny side of the sateen; the manufacturer advises using it within 6 months and storing it somewhere cool and dry, ideally in a sealed bag6. It works for patches, textile pictures or pieces that are later sewn onto a bag or a pillow. Its full details are on the page for Jacquard pretreated fabric.

Pretreated fabric doesn’t change how you care for the finished piece: it’s washed with the same precautions as fabric you’ve coated yourself.

Learn more: fabric for cyanotype, with the two options compared.

Before you start: protection and space#

Cyanotype reagents irritate the eyes, and ferric ammonium citrate, according to Jacquard’s data sheet, the skin as well8,9. Coat with nitrile gloves, sealed safety goggles and old clothes: the solution acts on any natural fiber it touches, including your T-shirt6. Work away from food and acids, because in contact with acids ferricyanide can release very toxic gases9.

Cover the table with plastic or paper: fabric is thinner than a sheet of watercolor paper and the solution soaks through. With children, the adult prepares and applies the chemistry, and Jacquard strongly recommends adult supervision6. All the details, with the safety data sheets, are in skin, clothing and textiles.

How to make a cyanotype on fabric, step by step#

Cyanotype on fabric takes seven steps in two stages: coating, under dim light and indoors, and exposure and rinsing, in the sun and with water. If it’s your first time, also coat a scrap of the same fabric: it will serve as a test strip to find the exposure time. To have everything at hand, print the cyanotype materials list.

Cyanotype on fabric, from new fabric to dry garmentSeven stages in a row. 1. Wash the fabric before coating it, as a precaution. 2. Mix only what you’ll use: according to Jacquard, the mixture is stable for 2 to 4 h. 3. Coat under dim light, by brush or by dipping. 4. Dry in the dark. 5. Expose with glass on top: 1 to 30 min in the sun according to Jacquard; well-exposed fabric looks bronze. 6. Rinse for at least 5 min, changing the water until it runs clear. 7. Dry in the shade: the blue matures in about 24 h. Below, a color band: pale yellow at stages 3 and 4, bronze at 5 and blue at 6 and 7.1Wash the fabricfirstprecaution2Mix only whatyou’ll usestable 2 to 4 h,per Jacquard3Coat underdim lightby brush orby dipping4Dry in the dark5Expose withglass on top1 to 30 min in sun,per Jacquard;well exposed looksshadows6Rinse at least5 minchanging the wateruntil it runsclear7Dry in theshadeblue matures inabout 24 hpale yellowshadowsbluedeep blueApproximate colors. Cyanotype on fabric, from new fabric to dry garment1Wash the fabric firstprecaution2Mix only what you’ll usestable 2 to 4 h, per Jacquard3Coat under dim lightby brush or by dipping4Dry in the dark5Expose with glass on top1 to 30 min in sun, per Jacquard; wellexposed it looks bronze6Rinse at least 5 minchanging the water until it runs clear7Dry in the shadethe blue matures in about 24 hThe color square is the approximate tone of the fabric atthat stage.
Diagram 1Cyanotype on fabric, from new fabric to dry garment. The seven stages of cyanotype on fabric with Jacquard’s figures and the color the fabric takes on at each point.
  1. Step 1: Wash the fabric before coating it

    Wash new fabric in water without fabric softener, and let it dry completely. It’s a common precaution to remove sizing, the finishes fabric has from the factory. We haven’t found a source that measures its effect, so we give it as a sensible precaution, not a rule. The alternative photography course at the University of Guanajuato also calls for washing manta cruda, unbleached cotton, beforehand, although it doesn’t say how10.

    If you use sodium carbonate to scour it, rinse it thoroughly before going on: the Getty Conservation Institute lists it among the alkalis that break down Prussian blue4. Any residue in the fiber would damage the image.

    How to tell it’s going well: the fabric is completely dry, smooth and doesn’t smell of fabric softener.

  2. Step 2: Mix the solution just before use

    If you use a powdered chemistry set, dissolve it ahead of time: Jacquard calls for 24 hours for its kit powder to dissolve fully in its bottle11. Mix the two solutions in equal parts only when you’re about to coat, because the mixture is stable for 2 to 4 hours, according to Jacquard’s instructions12. If you’d rather prepare the reagents yourself, follow the cyanotype formula.

    How much mixture? Jacquard gives no amounts per area for fabric12. It does state the yield of its set: about 65 prints of 20.3 × 25.4 cm (8 × 10 inches) on paper or about 50 on fabric3. From that it follows that fabric uses about 30% more solution than paper (our own calculation from the manufacturer’s figures). Ware’s estimate for paper, about 1.5 ml per print of that size spread with a rod, is meant for paper, not fabric2. Work out your starting point with the Sensitizer Calculator and mix a little more than you need.

    How to tell it’s going well: the mixture is a clear, greenish-yellow liquid13, with no trace of blue.

    Safety: Wear safety glasses and nitrile gloves to mix and brush on the solution; if it splashes into your eyes, rinse with plenty of water for 15 minutes. More on safety

  3. Step 3: Coat the fabric under dim light

    Work under dim light and away from the sun, as Jacquard says11. Pin the fabric to a plastic-covered board so it doesn’t move or wrinkle. Jacquard says the fabric can be painted or dipped in the sensitizer12: with a brush you control the area and the edges; dipped, the fabric soaks through completely.

    With a brush, spread the solution in crisscross strokes, without overloading, until the area is even. Irregular brushed edges are common in cyanotype: if you like them, leave a margin of untreated fabric around the edge. For how to choose the tool, see brushes for cyanotype.

    How to tell it’s going well: the coat is even, with no puddles or drips, and the fabric isn’t blue anywhere.

    Safety: Coat the fabric wearing nitrile gloves and old clothes: the solution stains skin and textiles. More on safety

  4. Step 4: Dry the fabric in the dark

    Let the fabric air-dry in the dark, as Jacquard’s instructions say12: flat inside a drawer or box, or hung in a dim room. It has to be completely dry before exposure, because Jacquard says not to wet the fabric before or during exposure14.

    Use it soon. We haven’t found a published time limit for fabric you coat yourself; for paper, Ware advises using it within a few hours or storing it cool, dark and dry2, and that’s the cautious guideline here too.

    How to tell it’s going well: the dry fabric is a pale, matte yellow. If the yellow coating turns green or blue in the dark, with paper Ware reads that as a sign of impurities2: coat another piece.

  5. Step 5: Compose and expose in the sun

    Set up the composition in the shade: the board, the fabric with the coated side up, the plants or objects and, on top, a sheet of glass held with clips. The simplest way to get good contact is to work on a flat surface with heavy glass on top12. The plants should be pressed and dry: Anna Atkins herself noted that with thick specimens she couldn’t press the glass down enough and the image came out imperfect15. We explain how to flatten them in how to press plants for cyanotype.

    Take the setup into the sun. For its chemistry, Jacquard gives 1 to 30 minutes depending on conditions, with no separate times for fabric and paper, and would rather you go over than fall short12. The claim circulates that fabric needs a fixed percentage more time than paper; we haven’t been able to confirm it in reliable sources, so we don’t give it.

    The reliable way to get it right is the test strip: expose the scrap in sections, covering one more each time, with times that double from one section to the next16. The right time may fall between two sections. The full method is in cyanotype exposure time.

    How to tell it’s going well: well-exposed fabric looks bronze12, and stays light under the plants. Don’t expect to see blue yet: it appears in the water.

    Safety: When exposing in the sun, protect yourself as you would for any time outdoors: shade while you wait, UV-blocking sunglasses and sunscreen; don’t look at the sun. More on safety

    Safety: With citrus, rue, fig, parsnip and other phototoxic plants, wear gloves: their sap plus UV light can burn the skin. More on safety

  6. Step 6: Rinse in water until it runs clear

    Remove the glass in the shade and put the fabric in a tray of clean water. Jacquard says to rinse for at least 5 minutes, changing the water from time to time, until it runs clear12, and to use a clean tray with no soap residue14. Avoid alkaline or very hard water, high in calcium salts: Ware warns that it degrades the image17.

    Don’t rinse longer than necessary. The water also carries off some of the blue: according to conservators cited by Ware, a 15-minute wash in tap water made some cyanotypes lose about 18% of their density18.

    How to tell it’s going well: the exposed areas turn blue when wet12 and no yellow tint is left in the whites. If there is, it needs more rinsing19.

    Safety: Keep leftover solution and the first wash bath in a closed, labeled container for your local hazardous waste collection point; later rinses can go down the drain with plenty of water. More on safety

  7. Step 7: Dry in the shade and wait for the final blue

    Gently squeeze out the fabric and hang it in the shade. Jacquard advises against drying it in direct sun14, and strong light fades cyanotype, although with air and darkness it recovers its blue18. Without hydrogen peroxide, the blue reaches its final tone by oxidizing over about 24 hours12.

    Hydrogen peroxide brings that blue out sooner during the rinse, but doesn’t change the density of the dry print2. If you want to use it, first read what hydrogen peroxide is for.

    How to tell it’s going well: the next day, the blue is darker and more even than when it came out of the water.

If something goes wrong#

If the fabric comes out pale, the most likely cause is that it didn’t get enough light; if it comes out blotchy, it’s almost always moisture or grease on the surface. This table sets out the most common failures on fabric, with the most likely cause and what to change on the next piece.

Common failures in cyanotype on fabric
What you see Most likely cause What to do
The blue comes out pale Short exposure: when in doubt, Jacquard advises going over rather than falling short12 Repeat with more time, based on a test strip
Pale after a long rinse The water carries off some of the blue18 Rinse until the water runs clear, no longer
The whites stay yellowish Not enough rinsing19 Rinse again in clean water
Blurry silhouettes The plant or object wasn’t touching the fabric12 Press the plants and use heavy glass
Blotches or faded areas Damp hands, sweat or skin oils14 Gloves and dry hands when handling the fabric
The blue yellows when the garment is washed Detergent with phosphates or an alkaline medium6 Phosphate-free detergent, cold water and infrequent washing

Learn more: why my cyanotype comes out light, with all the causes in order.

What circulates about cyanotype on fabric#

Recipes and figures circulate about textile cyanotype that we haven’t been able to confirm. This table lists them without repeating the figures: what reliable sources say, and what none of them say.

Cyanotype on fabric: what circulates and what the sources say
What you’ll hear What the sources say Source
Fabric needs a fixed percentage more exposure than paper Jacquard doesn’t give different times for fabric and paper with its chemistry; we haven’t found that percentage in reliable sources 12
You have to boil the fabric with sodium carbonate at a specific concentration Jacquard’s instructions don’t mention prewashing; sodium carbonate is an alkali that breaks down Prussian blue, so if it’s used, rinse thoroughly 4
It’s best to mordant the fabric with alum Jacquard doesn’t mention any mordant in its fabric instructions, and we haven’t found a reliable source to justify it 12
You have to rinse the garment with vinegar Jacquard’s fabric instructions don’t use it; we haven’t found a reliable source on its effect on fabric 12
Blends work above a certain percentage of cotton None of the sources consulted gives a percentage; Jacquard rules out polyester 6
Cyanotype on fabric doesn’t fade Sources disagree: Hu describes it as stable and fade-free; Jacquard considers it less washable than a dye and warns that overwashing lightens it 20,6

Caring for the garment after the first rinse#

A cyanotype fabric lasts if you look after it, but it doesn’t behave like a factory-dyed garment. Jacquard recommends washing it as little as possible, by hand, in cold water and with phosphate-free detergent, because phosphates and alkaline media can yellow the image and overwashing lightens it6.

The reason is chemical: Prussian blue holds up well in neutral or acidic conditions, but alkaline materials break it down quickly4. Jacquard adds that sweat and oils from the hands can also discolor it6, so a T-shirt worn every day suffers more than a pillow or a textile picture.

Learn more: how to wash a cyanotype T-shirt, covering detergents, washing machines and ironing.

Variations: color, paint and toning#

Cyanotype on fabric allows three simple variations: printing on colored fabric, adding color on top of the print and changing the blue with toning. All three come with a chemical condition worth knowing beforehand, because Prussian blue is transparent and sensitive to alkalis.

Colored or patterned fabric. Since cyanotype is transparent, it adds to the background: according to Jacquard, on yellow it comes out green, on red it comes out purple and on black it doesn’t show6. A floral or striped pattern stays visible under the blue.

Paint or dye on top. Jacquard allows adding color with dyes, paints or markers, but warns that if the product has a high pH the blue underneath may weaken or disappear, and advises testing first6. More ideas in mixed media on cyanotype.

Toning. Tea or coffee take the blue toward sepia tones; Jacquard describes this practice for its cyanotypes6. How to do it is in toning cyanotypes.

Fabric projects to start with#

With the process on this page you can make any textile piece; what changes between projects is preparing the garment, the composition and how it will be used afterward, which decides how often you’ll wash it. Each project has its own page with its specific steps and refers back here for the base technique.

Frequently asked questions

Can you make a cyanotype on colored fabric?

Yes, but the color of the fabric matters. Cyanotype is transparent, like a dye, so it adds to the background color: according to Jacquard, on yellow fabric the blue comes out green and on red, purple. On black fabric it doesn’t show. For the blue to read cleanly, start with white or unbleached cotton.

How much solution do I need for a T-shirt?

There’s no published figure per area for fabric. What Jacquard does state is the yield of its set: about 65 prints of 20.3 × 25.4 cm on paper or about 50 on fabric, which means about 30% more solution on fabric. Mix a little, coat, and make more only if you run short.

How long does coated fabric keep before exposure?

If you coat it yourself, we haven’t found a published time limit for fabric. For paper, Mike Ware advises using it within a few hours or storing it cool, dark and dry, and that’s the cautious guideline. Jacquard pretreated fabric is a different matter: the manufacturer advises using it within 6 months.

What happens if the fabric gets wet before exposure?

It can get blotchy. Jacquard says the surface and the objects you place on it should be dry, and that you shouldn’t wet the paper or fabric before or during exposure. That’s why the plants are pressed and dry, and the fabric is handled with gloves and dry hands.

Can children make cyanotypes on fabric?

Yes, with a clear division of tasks. The adult prepares and applies the solution, and the children compose with plants and objects, place the glass and watch the blue appear in the water. Jacquard strongly recommends adult supervision. With the youngest children, pretreated fabric avoids touching the reagents.

Your next step

Print your first cyanotype T-shirtA project for printing a cotton T-shirt with cyanotype: choosing the garment, coating only the design area, exposing, rinsing and caring for it.

Sources

  1. Image Permanence Institute. (n.d.). Cyanotype. Graphics Atlas. Rochester Institute of Technology. https://new.graphicsatlas.org/cyanotype Accessed October 17, 2026.
  2. Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026. 12345
  3. Jacquard Products. (n.d.). Cyanotype sensitizer set [Product page]. https://www.jacquardproducts.com/cyanotype-set Accessed October 16, 2026. 12
  4. Stulik, D. C. and Kaplan, A. (2013). Cyanotype. In The atlas of analytical signatures of photographic processes. Getty Conservation Institute. https://www.getty.edu/conservation/publications_resources/pdf_publications/pdf/atlas_cyanotype.pdf 1234
  5. Bilvar, H. (2025). Fotoğraf ve tekstilin kesişiminde siyanotip (cyanotype) baskı: Gelenekten geleceğe tekstil ve sanattaki rolü [Cyanotype printing at the intersection of photography and textiles: Its role in textiles and art, from tradition to the future]. Bodrum Journal of Art and Design, 4(1), 94–108. https://doi.org/10.58850/bodrum.1603461
  6. Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026. 1234567891011121314
  7. Jacquard Products. (n.d.). Cyanotype fabric sheets [Product page]. https://www.jacquardproducts.com/cyanotype-fabric-sheets Accessed October 16, 2026. 12
  8. Rupert, Gibbon & Spider, Inc. (2018). Safety data sheet: Ferric ammonium citrate (CHM1102, CHM2102, JCY1100). https://uwaterloo.ca/fine-arts/sites/default/files/uploads/documents/ferric-ammonium-citrate_2018-02-07.pdf. Accessed October 16, 2026.
  9. Honeywell Specialty Chemicals Seelze GmbH. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (version 2.4, ref. 31253). https://pdf.dutscher.com/doc/31253-1KG-HON/31253-1KG-HON_FDSen.pdf. Accessed October 16, 2026. 12
  10. Universidad de Guanajuato. (2022, February 8). Clase digital 11: Introducción a la fórmula y materiales y preparación de soportes y sustratos. Recursos Educativos Abiertos (UDA Fotografía alternativa, Licenciatura en Artes Visuales). https://blogs.ugto.mx/rea/?p=528 Accessed October 16, 2026.
  11. Jacquard Products. (n.d.). Cyanotype [Cyanotype Kit instruction booklet]. https://jacquardproducts.com/s/Cyanotype-Kit-INSTRUCTION-BOOKLET.pdf Accessed October 17, 2026. 12
  12. Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer’s instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026. 123456789101112131415
  13. Redden, H. and Crawford, A. (2025). Anna Atkins and the making of macroalgae cyanotypes and their role in science education. Applied Phycology, 6(1), 1-8. https://doi.org/10.1080/26388081.2024.2435049
  14. Jacquard Products. (2015). Cyanotype tips and troubleshooting [Manufacturer’s document, version 6.01.15]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Tips_and_Troubleshooting.pdf Accessed October 16, 2026. 1234
  15. Franchi, S. (2024). Crafting and collecting cyanotypes: Anna Atkins's Photographs of British Algae: Cyanotype Impressions. Literature Compass, 21(1-3), Article e12708. https://doi.org/10.1111/lic3.12708
  16. Ilford Photo. (2017, March 30). Making a black & white print: Exposure testing. https://www.ilfordphoto.com/exposure-testing/ Accessed October 16, 2026.
  17. Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026.
  18. Ware, M. (2003). A blueprint for conserving cyanotypes. Topics in Photographic Preservation, 10, 2-18. https://resources.culturalheritage.org/pmgtopics/2003-volume-ten/10_02_Ware.pdf 123
  19. Ware, M. (n.d.). The New Cyanotype process. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/New_Cyanotype_Process.html Accessed October 16, 2026. 12
  20. Hu, L. (2022). Design and application of cyanotype technology in cultural and creative products. BCP Social Sciences & Humanities, 18, 194-198. (supporting source)

Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.