Skip to content
The Cyano Codex
Choose language

Developing a cyanotype: washing, acid bath and oxidation

Developing a cyanotype means washing it in water: you wash until the yellow is gone from the whites, about 20 minutes of running water according to Mike Ware, and the blue finishes coming up as it dries. No fixer is needed. Here are the baths, the times, the optional acid bath and what to do with the water.
Section
Technique
Reviewed
Reading time
15 min
Sources
14
Level
Beginner (level 1 of 3)

As an Amazon Associate I earn from qualifying purchases. How we fund the site

Gloved hands lifting a freshly developed blue fern cyanotype out of a tray of water
Plate 1The blue comes up in cold water.
Time
About 20 min of washing, plus about 24 h until the final blue
Level
Beginner
Materials
9
Steps
6

In short

  • A cyanotype is developed in water alone: the wash removes the unexposed salts and no fixer is needed.
  • Wash until the yellow is gone from the whites; Ware estimates about 20 minutes in running water.
  • Overwashing also lightens the image, because the water carries off some of the blue.
  • Ware says not to wash with alkaline or hard water, which degrade the image.
  • The final blue arrives as the print dries, in about 24 hours; hydrogen peroxide brings it out sooner but doesn’t change it.
  • We recommend taking the first bath to a hazardous waste collection point; later rinses can go down the drain with plenty of water.

Safety: Keep leftover solution and the first wash bath in a closed, labeled container for your local hazardous waste collection point; later rinses can go down the drain with plenty of water. More on safety

Materials list

Check off what you already have on the table. The “Amazon” links are affiliate links.

To develop
  • How to chooseAmazon (affiliate): Nitrile gloves (opens in a new tab)
  • How to choose
To finish

Your check marks are saved only in this browser. No account needed.

On this page (7 sections)
  1. What happens in the water during development?
  2. Step by step
    1. 1. Set up the trays and the water
    2. 2. Optional: give it a first acid bath
    3. 3. Wash until the yellow is gone
    4. 4. Optional: bring out the blue sooner with hydrogen peroxide
    5. 5. Dry the print in the shade
    6. 6. Wait a day before judging it
  3. How long should you wash a cyanotype?
  4. Do you have to wait 24 hours to see the final blue?
  5. The acid bath: what it does and what concentration to use
  6. What do I do with the wash water?
  7. If something goes wrong

What happens in the water during development?#

During development, the water dissolves the salts that haven’t received light and leaves Prussian blue on the paper, the pigment formed during exposure1. That’s why cyanotype needs no fixer: Graphics Atlas sums up the only fixing needed as a 20-minute bath in running water2.

Development is the next-to-last stage of how to make a cyanotype. It comes right after exposure, when the print still shows a dull grayish blue and, with the classic formula, the shadows may look bronzed3. That tone is the sign of a full exposure and disappears in the water or as the print dries4,5.

Not all the blue stays on the paper. The classic formula forms what is called “soluble” Prussian blue, which doesn’t actually dissolve. Its particles are so fine that water disperses them and carries some away, which chemists call peptization5. Ware explains that with the classic formula a large part of the blue goes off with the water, and that the traditional answer has been heavy overexposure5,6.

The loss is partial: a dry cyanotype doesn’t stain your hands when you touch it, although water can carry off some pigment7. Hence the two rules on this page: wash enough to remove all the unreacted chemistry, and no more.

Step by step#

  1. Develop

    Step 1: Set up the trays and the water

    Set out two or three trays larger than the print, clean and kept for the workshop. Make sure they have no soap residue: Jacquard attributes yellow or brown discoloration to phosphates, soap or dirty objects8. Fill them with clean water and have a container with a lid and a label ready for the first bath.

    The water matters more than it seems. Ware says not to wash with alkaline water, with a pH above 7, or with hard water, rich in calcium salts, because they degrade the image9. pH is the measure of acidity: below 7 water is acidic and above it, alkaline. If you know your water is hard, at least do the first bath with distilled water, which is what Ware uses to make up his solutions10.

    Safety: Work away from food and drink, with dedicated tools that never go back to the kitchen. More on safety

    How to tell it’s going well: the trays are clean and full, and the first-bath container is open and at hand.

  1. Develop

    Step 2: Optional: give it a first acid bath

    For the classic formula, Ware says that adding a little dilute citric acid to the first bath can improve the image, although he doesn’t give the concentration10. The most specific figure he publishes is in his Simple Cyanotype: 1% citric acid, that is, 10 g per liter of water, for half a minute to a minute, with agitation9.

    Dissolve the acid in the tray water before putting the print in, with goggles on: PanReac’s data sheet classifies citric acid as an eye irritant11. Afterward, wash thoroughly, because Ware warns that poorly rinsed citric acid can make the print more prone to fading5.

    Safety: Use vinegar or citric acid only diluted in the bath water; never add them to the powders or to the classic-formula sensitizer. More on safety

    How to tell it’s going well: the water takes on a greenish-yellow tint, a sign that the unreacted sensitizer is coming out.

  1. Develop

    Step 3: Wash until the yellow is gone

    Move the print to clean water and wash it face down in a gentle stream of running water, or in several baths of still water. For the classic formula, Ware washes until the yellow of the sensitizer is completely gone from the highlights, and estimates that about 20 minutes is enough10. With his Simple Cyanotype, after the acid bath, about 10 minutes of running water or three or four baths of still water are enough for him9.

    Keep the water from the first bath in the labeled container, just like leftover solution: that’s our recommendation, because the ferricyanide data sheets say it must not reach the sewer system12. Later washes can go down the drain with plenty of water.

    Safety: Keep leftover solution and the first wash bath in a closed, labeled container for your local hazardous waste collection point; later rinses can go down the drain with plenty of water. More on safety

    How to tell it’s going well: when you look at the whites against the window light, no yellow or greenish tone is left.

  1. Develop

    Step 4: Optional: bring out the blue sooner with hydrogen peroxide

    If you want to see the final blue right away, immerse the print in a 0.3% hydrogen peroxide bath for half a minute at most, as Ware does5. In his Simple Cyanotype he makes it by adding 50 ml of 6% hydrogen peroxide, the “20 volume” kind, per liter to the first wash bath9. With 3% drugstore hydrogen peroxide, the same concentration takes about 100 ml per liter (our calculation).

    The bath doesn’t change the final density of the dry print: it only brings forward what the air would do anyway10. The other doses going around, and why we prefer this one, are in cyanotype with hydrogen peroxide.

    Safety: Use only 3% drugstore hydrogen peroxide, added to the bath water, and keep it away from your eyes. More on safety

    How to tell it’s going well: the blue darkens evenly within seconds.

  2. Finish

    Step 5: Dry the print in the shade

    Let the print drain without rubbing it and hang it with clips or lay it flat on a rack, out of the sun. A cyanotype is light-sensitive even when finished: an hour of direct sun fades it much more than the same amount of light received gradually6.

    It’s normal for the blue to darken as it dries. If what appears is yellow or greenish tones in the whites, it most likely needs more washing3: wash it again.

    How to tell it’s going well: the paper dries flat, without stains, and the blue gains depth over the hours.

  1. Finish

    Step 6: Wait a day before judging it

    The shadows come out of the water paler than they will end up and regain their blue little by little as they dry, through oxidation by the air; Ware estimates about 24 hours13. Jacquard gives the same time for its chemistry4. Before deciding whether you need more or less exposure, wait that day.

    How to tell it’s going well: the next day, the blue is deeper and more even than when it came out of the water.

Development at a glance: baths and timesFour stages from left to right, with an approximate color swatch of the print at each: grayish blue, medium blue and Prussian blue. 1. First bath, of water or, optionally, citric acid: Ware, for his Simple Cyanotype, uses 1% citric for 30 s to 1 min; this bath goes into the container for the hazardous waste collection point. 2. Wash, until the yellow is gone from the whites: with the classic formula, about 20 min of running water; Jacquard calls for at least 5 min, changing the water. 3. Optional: 0.3% hydrogen peroxide, 30 s at most; it brings out the blue sooner but doesn’t change it. 4. Dry in the shade: about 24 h until the final blue. Warning: no alkaline water and no hard water.1First bath: water or,if you like, citric acidWare, Simple Cyanotype: 1%citric, 30 s to 1 minthis bath goes in the wastecontainer2Washuntil the yellowis gone from the whitesclassic: about 20 min of waterwaterJacquard: at least 5 min,changing the water3Optional: hydrogen peroxideat 0.3%30 s at mostbrings blue out sooner, same result4Dry in the shadeabout 24 h to the final blueNo alkaline or hard water in any bath.Approximate color swatches. Development at a glance: baths and times1First bath: water or, if you like, citric acidWare, Simple Cyanotype: 1% citric, 30 s to1 minthis bath goes in the waste container2Washuntil the yellow is gone from the whitesclassic: about 20 min of running waterJacquard: at least 5 min, changing the water3Optional: 0.3% hydrogen peroxide30 s at mostbrings blue out sooner, same result4Dry in the shadeabout 24 h to the final blueNo alkaline or hard water in any bath.Approximate color swatches.
Diagram 1Development at a glance: baths and times. The development baths in order, with each source’s times and the color the print takes on as it goes. Approximate colors.

How long should you wash a cyanotype?#

A cyanotype is washed until the yellow of the sensitizer is completely gone from the whites: that’s the criterion the sources agree on. The minutes vary. For the classic formula, Ware estimates about 20 minutes of running water10, and Jacquard calls for at least 5 minutes, changing the water4.

What you’ll hear and what the sources say
What you’ll hear What the sources say Source
Three 5-minute baths Classic formula: until the yellow is gone from the highlights; about 20 minutes of running water 10
About 5 minutes At least 5 minutes, changing the water, until it runs clear (Jacquard chemistry) 4
Up to an hour Overwashing erodes the image; in tap water at pH 7.5–8.5, 15 minutes took away about 18% of the density 3,6
Five or six rinses The common criterion is color: wash until the greenish-yellow tint is gone; the only fixing needed, a 20-minute bath in running water 3,2

Time has a limit on each side. If you stop short, the print fades more in light: in one of Ware’s tests, the print washed for 4 minutes faded considerably more than the one washed for 206. If you overdo it, the water takes away image. Conservators cited by Ware measured a loss of about 18% of density in prints washed for 15 minutes in tap water with a pH between 7.5 and 8.56.

That’s why it’s better to go by color, not minutes. Wash until the whites are clean and stop there. If you record the washing time alongside the exposure time at each session, for example in the cyanotype test log, within a few sessions you’ll know how much your paper needs with your water.

Do you have to wait 24 hours to see the final blue?#

Yes: a cyanotype’s final blue appears after a day. The shadows come out of the water paler and darken as they dry, because oxygen in the air finishes oxidizing the pigment. Ware puts it at about 24 hours13, and Jacquard gives the same time for its chemistry4.

This has a practical consequence: a test strip or a print is judged dry, and the next day. If you decide on the exposure from the wet print, you’ll tend to overexpose the next one.

Hydrogen peroxide brings that change forward but doesn’t improve it. Ware uses it at 0.3% for half a minute at most, and notes that it doesn’t change the final density5. It’s a shortcut to see the result sooner, not a way to get a deeper blue than drying would give.

The acid bath: what it does and what concentration to use#

The acid bath is optional and serves to improve the tonal range. For his New Cyanotype, Ware explains that treating the print at the start in an acid bath, for one or two minutes, gives stronger shadows and a wider range5. In his Simple Cyanotype he measures the opposite effect: without an acid bath, developing in water alone, the tonal scale shortens and contrast rises9.

Ware’s figures don’t match across his own texts. For his New Cyanotype, his website mentions 1% nitric acid or 1–2% citric5. His 2009 workshop notes give 0.25–1% nitric for 5 to 10 minutes and leave citric as a last resort13.

Acid bath concentrations in Ware’s two texts
Acidic Ware’s workshop notes (2009) Ware’s website Who it’s for
Citric acid Only as a last resort13 1-2 %5 The household option; in Simple Cyanotype, 1%9
Nitric acid 0.25–1%, for 5 to 10 min13 Around 1%5 We don’t recommend it at home
Hydrochloric acid 0.25-1 %13 1 %5 We don’t recommend it at home
Sulfamic acid We don’t give it 1 %5 We don’t cover it: we haven’t reviewed its safety data sheet

Our approach: for the classic formula at home, 1% citric acid, Ware’s most specific and most cautious figure9. Ware warns that concentrated nitric acid is corrosive and gives off fumes, and he prepares it from a 10% stock solution13. He considers the final bath, diluted 100 to 400 times, not dangerous13. Even so, mineral acids are not for a home workshop.

Of vinegar, which is acetic acid, Ware says only that he doesn’t recommend it for his New Cyanotype13; the rest is in vinegar in cyanotype.

One rule holds for every acid: it goes diluted in the bath water, never in the powders or the sensitizer solution. The ferricyanide safety data sheets warn that in contact with acids it releases very toxic gases14. The recipe for the solution, with no acids, is in the cyanotype formula.

What do I do with the wash water?#

Wash water is split in two. The first bath goes into a closed, labeled container for the hazardous waste collection point, together with leftover solution, and later washes can go down the drain with plenty of water. That’s our recommendation, based on the ferricyanide safety data sheets12.

The data sheets treat ferricyanide residues as hazardous waste and say they must not reach the sewer system14. For citric acid, PanReac’s data sheet says the same for the product, but we haven’t found data on a 1% dilute bath11. If you use it in the first bath, that bath goes into the container anyway. How the collection point works and what to ask is in how to dispose of cyanotype waste.

If something goes wrong#

Almost everything that goes wrong in development shows up in the dry print. These are the most common failures and their most likely cause:

Frequently asked questions

What happens if I underwash a cyanotype?

Traces of sensitizer remain and show in the whites, which come out yellowish or greenish. Also, in one of Mike Ware’s tests, a print washed for only 4 minutes faded in light considerably more than one washed for 20 minutes. That’s why it’s worth washing until the yellow is completely gone, without dragging it out afterward.

Is the acid bath required?

No. A classic cyanotype develops well in water alone. Ware says a little dilute citric acid in the first bath can improve the image, and in his Simple Cyanotype he notes that developing in water alone shortens the tonal range and raises contrast. If you use it, rinse the print thoroughly afterward and never add the acid to the solution.

Can you dry a cyanotype in the sun?

Better not. A cyanotype is light-sensitive even when finished: Ware found that an hour of direct sun fades it much more than the same amount of light received at a lower intensity. Dry your prints hanging or flat, in the shade, and store them away from the sun.

Can you develop a cyanotype with tap water?

It depends on the water. Mike Ware says the wash water should not be alkaline or hard, rich in calcium salts, because it degrades the image, and conservators he cites saw prints washed for 15 minutes in tap water with a pH between 7.5 and 8.5 lose about 18% of their density. If your water is hard, at least do the first bath with distilled water.

Your next step

Bring out the blue sooner with hydrogen peroxideHydrogen peroxide brings out a cyanotype’s blue sooner but doesn’t change it. What concentration to use, for how long, and why sources give different doses.

Sources

  1. Stulik, D. C. and Kaplan, A. (2013). Cyanotype. In The atlas of analytical signatures of photographic processes. Getty Conservation Institute. https://www.getty.edu/conservation/publications_resources/pdf_publications/pdf/atlas_cyanotype.pdf
  2. Image Permanence Institute. (n.d.). Cyanotype. Graphics Atlas. Rochester Institute of Technology. https://new.graphicsatlas.org/cyanotype Accessed October 17, 2026. 12
  3. National Science and Media Museum. (2011, February 18). Introduction to the cyanotype process. National Science and Media Museum Blog. https://blog.scienceandmediamuseum.org.uk/introduction-cyanotype-process/ Accessed October 17, 2026. 12345
  4. Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer’s instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026. 123456
  5. Ware, M. (n.d.). The New Cyanotype process. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/New_Cyanotype_Process.html Accessed October 16, 2026. 1234567891011121314
  6. Ware, M. (2003). A blueprint for conserving cyanotypes. Topics in Photographic Preservation, 10, 2-18. https://resources.culturalheritage.org/pmgtopics/2003-volume-ten/10_02_Ware.pdf 12345
  7. Sentoku, S., Kurashina, M. and Kida, K. (2025). Observation of blue particles formed by photosensitizing reaction on paper fibres of cyanotypes. Photochem, 5(3), Article 18. https://doi.org/10.3390/photochem5030018
  8. Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026. 12
  9. Ware, M. (2022). Alternative photographic processes: Simple Cyanotype [PDF instructions]. https://mikeware.co.uk/downloads/SimpleCy22.pdf Accessed October 16, 2026. 1234567
  10. Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026. 123456
  11. Panreac Química S.L.U. (2025). Safety data sheet: Citric acid (version 9.04, art. 1808). https://deca.upc.edu/en/laboratories/latem/security/reactius-quimics/anhydrous-citric-acid-panreac.pdf. Accessed October 16, 2026. 12
  12. Sigma-Aldrich. (2026). Ficha de datos de seguridad: Hexacianoferrato(III) de potasio (version 11.0, ref. 244023). https://www.sigmaaldrich.com/ES/es/sds/sigald/244023. Accessed October 16, 2026. 12
  13. Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026. 123456789
  14. Thermo Fisher (Kandel) GmbH. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (revision 5, ref. A16946). https://deca.upc.edu/en/laboratories/latem/security/reactius-quimics/potassium-hexacyanoferrate-iii-fisher-scientific.pdf. Accessed October 16, 2026. 12

Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.