How to coat paper for cyanotype
As an Amazon Associate I earn from qualifying purchases. How we are funded
- Time
- A few minutes per sheet, plus about 1 h of drying in the dark
- Level
- Beginner
- Materials
- 11
- Steps
- 7
In short
- Ware estimates 1.5 ml for 20.3 × 25.4 cm with a glass rod; with a brush, up to twice that.
- For an A4 sheet that comes to about 1.8 ml with a rod and up to 3.6 ml with a brush.
- Work under dim bulb light, with no fluorescent lights or daylight.
- One or two drops of 20% Tween 20 per 10 ml help the paper absorb it.
- Dry, the paper should be pale yellow; if it turns green or blue, it’s fogged.
Safety: Work away from food and drink, with dedicated tools that never go back to the kitchen. More on safety
Materials list
Check off what you already have on the table. The “Amazon” links are affiliate links.
Learn more: the complete materials list, with the brush, the paper and the protection this step calls for.
Your check marks are saved only in this browser. No account needed.
On this page (6 sections)
Before you start#
Coating is the first stage of how to make a cyanotype: it turns an ordinary sheet of paper into a surface sensitive to ultraviolet light. Have the two stock solutions ready, ferric ammonium citrate and potassium ferricyanide, or the powder kit already dissolved. Jacquard says to allow 24 hours for its powder to dissolve completely1.
The light has to be dim. Mike Ware coats under soft tungsten bulb light and avoids fluorescent lights and daylight2, and Jacquard says to work in low light and away from the sun1. You don’t need darkness: you need to keep from giving the coating the light that would expose it too soon.
Protect the table, too. According to Jacquard, the solution takes on almost any natural surface, from cotton to wood or leather3, so it can stain the table blue: work on paper towels or plastic. Set up the protection before you open the bottles, and go over cyanotype safety if it’s your first time.
Which paper to use#
The paper has to survive the bath without falling apart and must not react with the solution. Ware calls for papers with no chalk alkaline buffer, that is, no calcium carbonate2, because calcium carbonate reacts badly with iron solutions4.
On the label, “acid-free” isn’t enough: a paper can be labeled acid-free and still contain a buffer, which is that alkaline reserve5. What you want to look for is “no alkaline buffer” or unbuffered, as Hahnemühle states for its Platinum Rag6. In Ware’s 2009 list, Fabriano Artistico and Canson Montval were among the buffered papers that require pretreatment2. Manufacturers can change the composition, so check the current data sheet.
Weight matters too. Ware considers 160 g/m² enough up to A4 size and calls for 240 g/m² or more for larger formats, so the paper doesn’t cockle when wet2. An 80 g/m² printer paper may not hold up to wetting and rinsing7. To choose at your leisure, see the guide to which paper to use for cyanotype.
Arches sells its Aquarelle block as 100% cotton 300 g/m² watercolor paper, with no optical brighteners and uncoated8. Whichever you choose, test it before buying in quantity: Ware points out that a manufacturer can change a paper’s composition without notice4.
How much solution does a sheet need?#
For a 20.3 × 25.4 cm print, Mike Ware estimates about 1.5 ml of mixed solution with a glass rod2. With a brush you can use up to twice as much9. For an A4 sheet that’s about 1.8 ml with a rod and up to 3.6 ml with a brush, by our calculation.
| Format | Surface | With a coating rod | With a brush, at most |
|---|---|---|---|
| 20.3 × 25.4 cm (Ware’s figure) | 516 cm² | 1.5 ml | 3 ml |
| A5, 14.8 × 21 cm | 311 cm² | 0.9 ml | 1.8 ml |
| Letter, 21.6 × 27.9 cm | 603 cm² | 1.75 ml | 3.5 ml |
| A4, 21 × 29.7 cm | 624 cm² | 1.8 ml | 3.6 ml |
| A3, 29.7 × 42 cm | 1,247 cm² | 3.6 ml | 7.3 ml |
The figures for each format are our own calculation from Ware’s figure, about 0.29 ml per 100 cm² with a rod2. Since the mixture is equal parts, half of each volume is citrate solution and the other half ferricyanide9. If you coat only a window within the sheet, calculate with that area in the Sensitizer Calculator.
This explains why one batch of formula goes so far. The 200 ml of Ware’s traditional recipe9, at 1.5 ml per 20.3 × 25.4 cm print, makes about 130 prints with a rod or about 65 with a brush (our calculation). These volumes apply to paper: according to Jacquard, its set makes about 65 prints on paper and about 50 on fabric, so fabric uses more10.
Brush or rod?#
You can get a good coat with a brush or a rod: what changes is the amount and the look of the edge. A glass rod uses less solution, and with a brush you can use up to twice as much, according to Mike Ware9. The brush, in exchange, leaves the marks of its strokes along the edges.
| Tool | What it offers | Keep in mind |
|---|---|---|
| Foam brush | The easiest to handle when starting out | Keep it for the workshop and rinse it when you’re done |
| Wide paintbrush | Edges with visible, very expressive strokes | Make sure it doesn’t shed hairs on the wet coating |
| Glass rod | Uses less solution9 | Takes practice and a very flat surface |
If you’re looking for other options, the guide to brushes for cyanotype compares types and sizes. Whichever you use, keep it for cyanotype only and don’t mix it with other paints.
Step by step#
- Prepare
Step 1: Prepare the table and the sheet
Draw the curtains or turn off the fluorescent lights, leave a dim bulb on and cover the table with paper towels2. Lightly mark in pencil the rectangle you’re going to cover and tape the sheet down at the corners with masking tape, so it doesn’t move under the brush.
How to tell it’s going well: you can read the labels on the bottles, but no direct sun falls on the table.
- Prepare
Step 2: Measure and mix only what you’ll use
Put on your gloves and goggles. With the syringe, measure equal volumes of the citrate solution and the ferricyanide solution and pour them into a small cup: the mixture is always equal parts9. Work out the amount with the table above, because the mixture doesn’t keep long: Ware speaks of days9 and Jacquard, for its kit, of a few hours1.
If you like, add the wetting agent: Ware recommends one or two drops of 20% Tween 20 per 10 ml of mixture, so the paper absorbs it better9. Very absorbent papers may not need it, hard-sized papers coat better with it, and with gelatin-sized papers it may react badly2.
Safety: Wear safety glasses and nitrile gloves to mix and brush on the solution; if it splashes into your eyes, rinse with plenty of water for 15 minutes. More on safety
How to tell it’s going well: the mixture is a clear, greenish-yellow liquid with no trace of blue.
- Coat
Step 3: Spread the solution
Load the brush without letting it drip and spread the solution inside the rectangle with strokes in one direction; then go over it in the opposite direction until the coat looks even, with no puddles or dry spots. A glass rod uses less solution than a brush2; if you’ve never used one, start with a brush and try the rod later.
Touch the paper only by the edges and with dry gloves: according to Jacquard, damp hands can leave marks on coated paper11.
How to tell it’s going well: the wet coat shines evenly and the brushed edges sit where you want them.
- Coat
Step 4: Optional: apply a second coat
If you want denser prints, Jacquard says paper can be coated twice11. We haven’t found a reliable source that says whether to dry between coats, so try it first on an offcut of the same paper.
How to tell it’s going well: compared with a single-coat sheet, both washed and dried, the double coat gives a deeper blue.
- Coat
Step 5: Let it dry in the dark
Carry the sheet flat to a drawer or box and let it dry at room temperature. Ware estimates about an hour, or about 5 minutes with warm air at about 40 °C2, and Jacquard also calls for air-drying in the dark11. In his Simple Cyanotype, Ware notes that heat drying raises the contrast slightly, by about one stop, that is, as if the light were doubled or halved12.
How to tell it’s going well: the coating no longer shines, the paper is matte and doesn’t feel cool to the touch.
- Coat
Step 6: Check the color before exposing
Dry, the paper should be pale yellow. If it turns green or blue before exposure, it has chemical fog, a tone that doesn’t come from light and tints the whites2. Ware attributes it to impurities in the paper2. That’s why it’s worth testing each new paper by coating an offcut and leaving it in the dark.
How to tell it’s going well: the yellow is even, with no green streaks or darker areas.
- Coat
Step 7: Clean up
Don’t pour leftover mixture back into the stock solution bottles. Keep it in a closed, labeled container for the hazardous waste collection point, together with the first wash bath, because the ferricyanide safety data sheets say it must not reach the sewer system13. Rinse the brush and cup, let them dry and store them with the rest of your workshop materials.
Safety: Keep leftover solution and the first wash bath in a closed, labeled container for your local hazardous waste collection point; later rinses can go down the drain with plenty of water. More on safety
The paper is now ready to expose. How long it can wait and how to store it is explained in how long coated paper lasts.
If something goes wrong#
Failures from this stage show up later, in the washed print, but almost all of them start here. These are the most common:
- Streaks or an uneven coat. A wetting agent like Tween 20 makes it much easier to spread the solution evenly14. The other causes are in streaks and uneven coating.
- Marks that don’t come from light. Damp hands can leave marks on coated paper11.
- Bluish whites. If the paper was already green or blue before exposure, it had chemical fog2.
- Cockled paper. Very wet paper may not lie flat because the fibers swell2; a heavier weight cockles less2.
If the problem shows up on one sheet and not the others, suspect the sheet or how you handled it first; if it shows up on all of them, suspect the paper or the mixture.
Frequently asked questions
Can you coat with an ordinary paintbrush?
Yes, as long as it’s wide, doesn’t shed bristles and you keep it for the workshop. What changes with the tool is the amount: according to Mike Ware, a brush can use up to twice as much solution as a glass rod. A foam brush is the easiest to handle when starting out, and a paintbrush leaves edges with more visible strokes.
How many coats of solution should you apply?
One is enough to start. Jacquard says paper can be coated twice for denser prints, but we haven’t found a reliable source that says whether to dry between coats. If you try it, do it on an offcut of the same paper and compare the result with a single coat.
Can you dry coated paper with a hair dryer?
Ware does it with warm air at about 40 °C for about 5 minutes, as an alternative to an hour of drying at room temperature. In his Simple Cyanotype he adds that heat drying raises the contrast slightly, by about one stop. If you use a hair dryer, keep the light dim while the paper dries.
Why has my coated paper turned green?
Because it has chemical fog: the coating has reacted without light and the whites will come out tinted. Mike Ware attributes it to impurities in the paper. That’s why it’s worth testing each new paper by coating an offcut and leaving it in the dark: if it stays pale yellow, the paper is fine; if it turns green or blue, it’s better to switch papers.
Does the room have to be dark to coat paper?
No. Dim light is enough: Mike Ware coats under tungsten bulb light and avoids fluorescent lights and daylight, and Jacquard says to work in low light and away from the sun. What does need darkness is the drying, in a drawer or a closed box.
Your next step
Sources
- Jacquard Products. (n.d.). Cyanotype [Cyanotype Kit instruction booklet]. https://jacquardproducts.com/s/Cyanotype-Kit-INSTRUCTION-BOOKLET.pdf Accessed October 17, 2026. 123
- Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026. 123456789101112131415
- Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026.
- Ware, M. (1995). A handmade paper for alternative processes. Ag+ Photographic, (7), 34–39. Reproduced at https://www.mikeware.co.uk/pages/main/technical/Alternative_Printing.html 12
- Northeast Document Conservation Center. (2018). Storage enclosures for photographic materials (Preservation Leaflet 5.6). https://www.nedcc.org/free-resources/preservation-leaflets/5.-photographs/5.6-storage-enclosures-for-photographic-materials Accessed October 17, 2026.
- Hahnemühle. (n.d.). Platinum Rag: Uncoated FineArt paper for platinum printing & other alternative processes [Product page]. https://www.hahnemuehle.com/en/stationery/finenotes/p/Product/show/241/810.html Accessed October 16, 2026.
- Redden, H. and Crawford, A. (2025). Anna Atkins and the making of macroalgae cyanotypes and their role in science education. Applied Phycology, 6(1), 1-8. https://doi.org/10.1080/26388081.2024.2435049
- Arches. (n.d.). Arches Aquarelle watercolor block, hot press, 9 × 12 in [Product listing, Amazon.com, ASIN B01AML7K9A]. Accessed October 24, 2026.
- Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026. 12345678
- Jacquard Products. (n.d.). Cyanotype sensitizer set [Product page]. https://www.jacquardproducts.com/cyanotype-set Accessed October 16, 2026.
- Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer’s instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026. 1234
- Ware, M. (2022). Alternative photographic processes: Simple Cyanotype [PDF instructions]. https://mikeware.co.uk/downloads/SimpleCy22.pdf Accessed October 16, 2026.
- Sigma-Aldrich. (2026). Ficha de datos de seguridad: Hexacianoferrato(III) de potasio (version 11.0, ref. 244023). https://www.sigmaaldrich.com/ES/es/sds/sigald/244023. Accessed October 16, 2026.
- Ware, M. (n.d.). The New Cyanotype process. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/New_Cyanotype_Process.html Accessed October 16, 2026.
Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.