Skip to content
The Cyano Codex
Choose language

Cyanotype wedding invitations

Cyanotype wedding invitations bring each guest the silhouette of an olive branch, a few wheat stalks or flowers from the bouquet, in white on Prussian blue, and no two come out alike. They call for cotton paper, a well-organized batch and an early decision about where the text goes. This project goes from the design to the envelope.
Section
Projects
Reviewed
Reading time
10 min
Sources
10
Level
Intermediate (level 2 of 3)

As an Amazon Associate I earn from qualifying purchases. How we fund the site

Cotton cards with cyanotypes of an olive branch next to white envelopes and a sprig
Plate 1Invitations with an olive branch in blue.
Time
Two or three sessions for a hundred cards, plus drying time; start with weeks to spare
Level
Intermediate
Materials
10
Steps
6

In short

  • Each invitation is one of a kind: the same plant leaves slightly different silhouettes on each card.
  • Cotton paper with no alkaline buffer, coated in large sheets and cut afterward.
  • For 100 A6 cards coated by brush, about 90 ml of sensitizer is enough (our own calculation from Ware’s figure).
  • The text goes on a separate card or in the negative itself; there’s no data on printing on top.
  • Expose the whole batch with the same light and the same time, after a test strip.

Safety: Wear safety glasses and nitrile gloves to mix and brush on the solution; if it splashes into your eyes, rinse with plenty of water for 15 minutes. More on safety

Safety: When exposing in the sun, protect yourself as you would for any time outdoors: shade while you wait, UV-blocking sunglasses and sunscreen; don’t look at the sun. More on safety

Materials list

Check off what you already have on the table. The “Amazon” links are affiliate links.

To coat
To prepare
To expose
  • How to choose
To develop
To finish

Your check marks are saved only in this browser. No account needed.

On this page (5 sections)
  1. What are cyanotype wedding invitations like?
  2. Before you start
  3. The invitations, step by step
    1. 1. Decide on the design and where the text goes
    2. 2. Prepare the image
    3. 3. Choose the paper and work out the sensitizer
    4. 4. Coat in batches
    5. 5. Expose the whole batch the same way
    6. 6. Wash, dry, cut and assemble
  4. Variations
  5. Caring for the invitations

What are cyanotype wedding invitations like?#

Cyanotype wedding invitations are cotton paper cards with a white silhouette on Prussian blue: a sprig of olive, a few wheat stalks, flowers from the bouquet. They’re made in batches, on large sheets that are cut afterward, and the text goes on a separate card or in the negative itself.

No two are alike, and that’s part of the appeal. Each of Anna Atkins’s plates is one of a kind, even when it reproduces the same specimen as others1, and the same goes for invitations. The plant sits a little differently on each card, and you can see it in the edge of the silhouette.

Before you start#

This project assumes you know the technique: how to coat, expose and wash is in how to make a cyanotype step by step. If you’ve never done it, make a few test prints weeks ahead. For the card’s composition, see also composition in botanical cyanotype.

If you’d rather not mix chemistry, you can make the invitations with pre-coated paper, which already has the dry sensitized layer: you cut it, expose it and wash it. You lose the choice of paper and the brushstroke edge, but you save time.

The invitations, step by step#

Cyanotype wedding invitations are made in six steps: decide on the design and the text, prepare the image, choose the paper and work out the sensitizer, coat in batches, expose in series, and cut and assemble. Organization matters as much as technique: a hundred cards means a hundred exposures.

How a batch of invitations comes out of one A4 sheetAn A4 sheet divided into four A6 cards with their trim margin, and an arrow pointing to a row of four cut cards. Below, a table: 25 A4 sheets make 100 A6 cards; with a coating rod you need about 45 ml of sensitizer, and with a brush about 90 ml (our own calculation from Ware’s figure). Beside it, the order of work: test strip; same light and same time for the whole batch; cut after washing and drying.1 A4 sheet = 4 A6 cards25 A4 sheets100 A6 cardsSensitizer, coating rodabout 45 mlSensitizer, brushabout 90 mlOur own calculation from Ware’s figure.Order of work1Test strip before the batch2Same light and same time for the wholebatch3Cut after washing and drying How a batch of invitations comes out of one A4 sheet1 A4 sheet = 4 A6 cards25 A4 sheets100 A6 cardsSensitizer, coating rodabout 45 mlSensitizer, brushabout 90 mlOur own calculation from Ware’s figure.Order of work1Test strip before the batch2Same light and same time for the whole batch3Cut after washing and drying
Diagram 1How a batch of invitations comes out of one A4 sheet. Four cards per sheet and a single exposure test for the whole batch; the sensitizer, worked out from Ware’s figure.
  1. Prepare

    Step 1: Decide on the design and where the text goes

    Choose the card format and how many fit on a sheet: four A6 per A4, or two A5. Decide early where the names, date and venue will go, because it changes the rest of the work.

    There are two safe options. The simplest is a separately printed card that goes in the envelope with the cyanotype. The other is to include the text in a negative so it comes out white on the blue. Printing the text on top of the finished cyanotype is a tempting idea, but we haven’t found published data on how the blue holds up with ink on top: if you want to try it, test it first on a spare card.

    How to tell it’s going well: you have a full-size sample card drawn out, with the image and the text in place.

  2. Prepare

    Step 2: Prepare the image

    If you’re using a plant, press several matching specimens, one for each card you’ll expose at the same time, plus a few extra. Choose thin, flat plants that repeat the silhouette well. If you’re using a negative with text or an illustration, print it on acetate at the exact size of the card: how to prepare it is in how to make a negative for cyanotype.

    How to tell it’s going well: you have as many plants or negatives as cards you’ll expose at once.

  3. Coat

    Step 3: Choose the paper and work out the sensitizer

    Use cotton paper with no alkaline buffer, the calcium carbonate additive that chemist Mike Ware advises against for cyanotype2. Ware gives 160 g/m² as a sufficient weight for sheets up to A42; for a card that gets handled and kept, a heavier paper feels better. How to read the label is in paper for cyanotype.

    For the sensitizer, Ware estimates about 1.5 ml per 20.3 × 25.4 cm print spread with a coating rod, and up to twice that with a brush3. This table comes from that and is our own calculation; always make a bit extra. If you use a powdered set, Jacquard states that theirs makes about 65 prints of 20.3 × 25.4 cm on paper4: cut into four, that would be about 260 cards of 10.2 × 12.7 cm (our own calculation).

    Mixed sensitizer for 100 cards (our own calculation from Ware’s figure)
    Card Sheets you coat With a coating rod With a brush
    A6 (10.5 × 14.8 cm), four per A4 25 A4 sheets about 45 ml about 90 ml
    A5 (14.8 × 21 cm), two per A4 50 A4 sheets about 90 ml about 180 ml

    How to tell it’s going well: you have paper for all the cards, plus the test strip and a few spare sheets.

  4. Coat

    Step 4: Coat in batches

    Coat the sheets in batches you can expose on the same day: sensitized paper is best used soon, and Ware advises using it within the next few hours or storing it cold, dark and dry2. Work in dim light, spread the sensitizer with crisscross strokes and leave a white margin around each card.

    How to tell it’s going well: the dry sheets are an even pale yellow, with no streaks or green patches.

    Safety: Wear safety glasses and nitrile gloves to mix and brush on the solution; if it splashes into your eyes, rinse with plenty of water for 15 minutes. More on safety

  5. Expose

    Step 5: Expose the whole batch the same way

    Before the first sheet, make a test strip with an offcut of the same paper: expose it in sections, doubling the time from one section to the next5. The time depends on the formula, the light, the paper and, in the sun, the time of day and the clouds6, so expose the whole batch in the same session, with the same light and the same time.

    Lay out the plants in the shade and in soft light, out of direct sun7, and close each board with its glass. If you have several, you can expose several sheets at once.

    How to tell it’s going well: all the sheets in the batch have changed color evenly around the plants.

    Safety: When exposing in the sun, protect yourself as you would for any time outdoors: shade while you wait, UV-blocking sunglasses and sunscreen; don’t look at the sun. More on safety

  6. Finish

    Step 6: Wash, dry, cut and assemble

    Wash the sheets until the yellow is gone from the whites3, let them dry flat and wait for the blue to mature: it darkens in the air over about 24 hours, according to Ware and Jacquard2,8. If any have cockled, leave them overnight between blotting paper with a weight on top.

    Safety: Keep leftover solution and the first wash bath in a closed, labeled container for your local hazardous waste collection point; later rinses can go down the drain with plenty of water. More on safety

    Cut the cards with a craft knife and a metal ruler, on a cutting mat. Pair each one with its text card, put them in the envelope and, if you like, tie them with linen ribbon.

    How to tell it’s going well: the cards are flat, with clean cuts and the plant in the same place on all of them.

Variations#

The same technique works for all the wedding stationery, and each piece can repeat the plant from the invitation for a unified look. Here are a few ideas; the first two use the same method, and the others need the format adjusted.

Menus and place cards. A narrow strip with a wheat stalk or a leaf for each guest.

Thank-you cards with flowers from the bouquet. After the wedding, press a few flowers from the bouquet and use them on the thank-you cards. How to work with flowers is in cyanotype with flowers.

Save-the-date postcards. A postcard format with the same plant, sent months ahead. We explain it in cyanotype postcards.

Color or hand calligraphy. You can write or paint on a cyanotype, but Jacquard warns that high-pH paints or dyes can weaken the blue or make it disappear9. Always test on a spare card.

Caring for the invitations#

Invitations are pieces many guests keep, so you want them to last. What damages them most is strong light: Ware found that an hour of direct sun fades a cyanotype much more than the same amount of light received at lower intensity10. Until you send them, keep them in a box in the dark.

If one fades from light, a few days in the dark bring back almost all of its blue: in Ware’s tests, at least 95% of its density in a day10. For more projects like this, see cyanotype ideas.

Frequently asked questions

How many invitations can you get from one chemistry set?

Quite a few. Jacquard states that its set makes about 65 prints of 20.3 × 25.4 cm on paper. If each print is cut into four, that’s about 260 cards of 10.2 × 12.7 cm (our own calculation from the manufacturer’s figure). A brush uses more than a coating rod, so allow some margin.

Can you print the names on top of the cyanotype?

We haven’t found published data on how the blue holds up to ink printed on top, so we can’t recommend it as a tested technique. The safe options are to put the text on a separate card or include it in the negative so it comes out white on the blue. If you want to try printing on top, test it first on a spare card.

Do all the invitations come out the same?

Not quite, and that’s part of their charm. The same plant sits a little differently on each card, and each print is one of a kind, as Anna Atkins’s plates were. For a consistent batch, use the same plant, the same paper, the same light and the same exposure time.

How far ahead should you make the invitations?

With time to spare. Allow one session to prepare the paper, one or more to expose and wash, and at least a day for the blue to mature as it dries, plus cutting and assembly. And keep spare sheets for redoing any that go wrong and for the test strip.

Your next step

Design your invitation’s compositionHow to compose a botanical cyanotype print: main subject and supporting elements, format and margin, dry mock-up, layout, label and framing.

Sources

  1. Franchi, S. (2024). Crafting and collecting cyanotypes: Anna Atkins's Photographs of British Algae: Cyanotype Impressions. Literature Compass, 21(1-3), Article e12708. https://doi.org/10.1111/lic3.12708
  2. Ware, M. (2009). New Cyanotype: Siderotype workshop notes. https://www.mikeware.co.uk/downloads/CyanoWork.pdf Accessed October 17, 2026. 1234
  3. Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026. 12
  4. Jacquard Products. (n.d.). Cyanotype sensitizer set [Product page]. https://www.jacquardproducts.com/cyanotype-set Accessed October 16, 2026.
  5. Ilford Photo. (2017, March 30). Making a black & white print: Exposure testing. https://www.ilfordphoto.com/exposure-testing/ Accessed October 16, 2026.
  6. Ware, M. (n.d.). The New Cyanotype process. Mike Ware: Alternative photography. https://www.mikeware.co.uk/mikeware/New_Cyanotype_Process.html Accessed October 16, 2026.
  7. Redden, H. and Crawford, A. (2025). Anna Atkins and the making of macroalgae cyanotypes and their role in science education. Applied Phycology, 6(1), 1-8. https://doi.org/10.1080/26388081.2024.2435049
  8. Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026.
  9. Jacquard Products. (2019). Cyanotype FAQs [Manufacturer’s document, version 02.08.19]. https://cdn.shopify.com/s/files/1/2714/2506/files/Cyanotype-FAQs.pdf Accessed October 17, 2026.
  10. Ware, M. (2003). A blueprint for conserving cyanotypes. Topics in Photographic Preservation, 10, 2-18. https://resources.culturalheritage.org/pmgtopics/2003-volume-ten/10_02_Ware.pdf 12

Reviewed on October 16, 2026. If you spot an error or a missing source, write to us and we’ll look into it.