Skip to content
The Cyano Codex
Choose language
Row of contact printing frames with plants exposing in the sun against a whitewashed wall
The same sheet in three states: coated, exposed and washed.

The Journal: The Cyano Codex blog · No. 22

Cyanotype for beginners: your first print, step by step

This page takes you from an empty table to your first print hanging up to dry. What to buy on day one, what to do with it, how long each step takes, what usually goes wrong and what precautions to take. It is meant to be read right through without leaving the page, and every section links to the long guide if you want to go deeper.

Published
Reviewed
Reading time
9 min
Sources
7

As an Amazon Associate I earn from qualifying purchases. How we are funded

In short

  • The shortest way in is ready-made cyanotype paper: the chemistry is already in the sheet and all it asks for is sun and water.
  • The print is made by contact, so it comes out the same size as the object or the negative you lay on top.
  • There is no universal exposure time: it depends on the light, the paper and the formula, and you dial it in with a test strip.
  • Grey or bronze shadows when you take the print out of the sun are not a fault: they mean the light has been enough.
  • It is developed with water alone and needs no fixer; Ware reckons about 20 minutes of running water.
  • The final blue does not appear until the print dries, in about 24 hours.
  • If you handle the chemistry, goggles and nitrile gloves from the moment you open the bottle; the first wash bath goes to a hazardous waste point.
On this page (8 sections)
  1. What a cyanotype is, in two sentences
  2. Where to start if it is your first time
  3. What to buy on day one
  4. Your first print, step by step
  5. The five things that go wrong most often
  6. The minimum you need to know about safety
  7. What to do with the water and the leftovers
  8. What to do once it works

What a cyanotype is, in two sentences#

Cyanotype is a camera-less photographic process: two iron salts spread on paper form Prussian blue wherever ultraviolet light reaches them, and water carries away whatever has not reacted1. John Herschel described it in 1842, and from 1843 Anna Atkins used it to illustrate a whole book of algae2.

What matters at the start is that it prints by contact: whatever you lay on the paper comes out at life size. A fern frond gives a silhouette the size of the frond; a photograph needs a negative printed at the size you want the print. There is no enlarger and no camera involved.

If you want the detail of the reaction, it is in what cyanotype is.

Where to start if it is your first time#

There are three routes, and for a first print only one makes sense.

Ready-made paper. The chemistry comes dry in the sheet. You open the envelope in dim light, lay a few leaves on top, take it out into the sun and wash it with water. Nothing to weigh, nothing to mix and nothing to store. It is what a workshop with children starts with, and it is what you should start with.

A kit with the chemistry. Two bottles with the chemicals already weighed out, which you dissolve in water and mix in equal parts. It goes much further and lets you choose the paper, but now you are handling chemicals.

The chemicals separately. You buy green ferric ammonium citrate and potassium ferricyanide on their own and make up the solutions yourself. It is the cheapest per print and gives the most control, and it is also the one that demands the most care.

The advice is simple: make two or three prints on ready-made paper before you buy any chemistry. You will know whether the process grabs you, and you will have learned to read the light, which is the part that is really hard. The full comparison is in the five types of kit.

What to buy on day one#

For the short route, this is more than enough:

What you need for a first session
WhatHow muchWhat for
Pre-coated cyanotype paperA small packThe chemistry comes in the sheet; nothing to prepare
A sheet of ordinary glass, or a picture frame1Pressing the objects flat against the paper
Leaves, dried flowers or flat objectsAs many as you likeThe silhouette comes out at life size
A tray larger than the sheet1Washing the print in cold water
Nitrile gloves1 pairFor the wash, even though the chemistry is in the sheet

The rest is already at home: a tray or a basin, some clips, a clock and a shady spot to hang things. If you move on to the chemistry, the whole list, with quantities and what to look for in each item, is in what you need to make cyanotypes.

A warning about the glass, because it is the most common buying mistake: ask for ordinary glass. Laminated glass and UV-filtering glass block exactly the light the print needs, and polycarbonate normally blocks radiation below about 370 nm3. A cheap picture frame with its glass will do.

Your first print, step by step#

1. Pick the day and the hour. A clear day, around midday. It is not essential: ultraviolet still gets through an overcast sky, about a third of it according to the EPA, but it will take considerably longer, and the first time it pays not to complicate things.

2. Lay out the composition in dim light. Indoors, away from the window, take the sheet out of its envelope and arrange on top whatever you want to print: dried leaves, lace, a key, a pair of scissors. Put the glass over it so everything is pressed flat against the paper. Anything that does not touch the paper will come out blurred or ghostly.

3. Carry the whole thing out into the sun in one go. Without stopping to look at it on the way. The sheet starts yellow or yellow-green and, as the light hits it, turns a bluish grey.

4. Bring it in when the shadows look bronzed. That is the signal: a brownish grey or bronze in the exposed areas4. It is not a defect, it is the sign that the light has been enough. Take it in earlier and the print will come out pale.

5. Wash in cold water. Take off the glass and the objects and put the sheet in the tray. The water carries away the chemistry that has not reacted: no fixer is needed5. Wash until the yellow has gone from the whites; Ware reckons about 20 minutes of running water1. Washing too long also lightens the image, because the water takes some of the blue with it.

6. Hang it to dry in the shade and wait. Here is the part that throws everybody: straight out of the wash the print looks weak and greyish blue. The final blue arrives as it dries, in about 24 hours, because the air finishes oxidising the pigment1. Do not judge your first cyanotype until the next day.

The full procedure, with the five stages and their variants, is in how to make a cyanotype step by step.

The five things that go wrong most often#

It comes out very pale. The likeliest cause is too little sun; when in doubt, overdo it rather than fall short. Washing too long also lightens it.

The whites come out yellow-green. The wash was too short. Put it back in clean water.

The silhouettes come out blurred. The object was not pressed firmly enough against the paper. More weight on the glass, or a frame with clips.

The print fades or whitens over time. Something alkaline has touched it: a detergent with phosphates, a board with an alkaline buffer, a buffered mat. Alkaline materials damage Prussian blue irreversibly.

The coated paper turned green or blue before exposure. It got too much light while drying, and the whites will come out fogged. Once dry, the paper should be a pale, matt yellow.

Every symptom, with its cause and its fix, is in common cyanotype problems.

The minimum you need to know about safety#

With ready-made paper the risk is small: the chemistry is dry in the sheet and you handle it with clean hands and, for the wash, with gloves. With loose chemistry things change, and it is worth being clear about that before you open the first bottle.

The classic chemicals irritate the eyes, and according to Jacquard's data sheet the citrate irritates the skin as well6. That is why you work in safety goggles and nitrile gloves from the moment you open the bottle until the first wash. The solution stains clothing and any natural fibre, so an old apron is a good idea.

The rule that is not up for negotiation: never mix ferricyanide with acids. In contact with an acid it can release highly toxic gases7. No vinegar, no cleaning products, no drain unblockers on the same table. Store it apart.

And never use kitchen utensils: the scale, the beakers and the trays that come into the workshop do not go back to the kitchen. The full detail is in how to work safely with cyanotype.

What to do with the water and the leftovers#

Leftover solution and the first wash bath go into a closed, labeled bottle, and from there to a hazardous waste point. Later washes can go down the drain with plenty of water.

The reason is not alarmist: ferricyanide is toxic to aquatic organisms, and algae are the most sensitive7. The waste bottle is also kept in the dark, because dissolved in water and exposed to light it can release free cyanide. Never into the garden, never into a river.

More, with the by-laws and what we have not found supported, in how to dispose of cyanotype waste.

What to do once it works#

Once you have three or four decent prints, there are three paths and none is better than the others.

Plants. It is how almost everyone comes in: pressed leaves and flowers give clean silhouettes, and it is what Anna Atkins did. Start with how to press plants for cyanotype, because a badly dried plant ruins the print.

Photographs. This calls for a negative the size of the print, output on transparency film. It is in how to make a negative for cyanotype.

Fabric. T-shirts, bags, scarves. Little changes compared with paper, and what does change is in cyanotype on fabric.

And if you want to stop depending on the sun, a 365 nm ultraviolet lamp gives you the same print in winter and at night: how to choose one.

More from the Journal

Frequently asked questions

Can you make cyanotypes without buying chemicals?

Yes, with ready-made paper: the chemistry is dry in the sheet and you only add sun and water. What does not exist is cyanotype from kitchen ingredients; what is sometimes sold as “home-made cyanotype” is really anthotype, a different process that uses plant pigments and needs weeks of sun instead of minutes.

How long does a cyanotype take?

Exposure runs from a few minutes to a good half hour depending on the light, the paper and the formula, and the wash about 20 minutes of running water. But the final blue does not arrive until the print dries, in about 24 hours. End to end, count on an afternoon of work and a day of waiting.

Do I need a darkroom?

No. A dim corner with soft bulb light, no fluorescents and no direct sun, is enough. Coated, dry paper is kept in the dark until it is time to expose, and that is all it takes.

Why is my first print so pale?

Almost always because the exposure was short. The sign that the light has been enough is the grey or bronze shadows when you take the print out of the sun: if the exposed areas are still yellowish, it needs more. The second cause is washing too long, because the water takes some of the blue with it.

Does any paper work?

No. It has to stand up to water and carry no alkaline buffer, because alkaline materials break down Prussian blue. Cotton watercolor paper is the safe bet: according to Ware, 160 gsm is enough up to A4, and 240 gsm or more is advisable at A3 or larger. Watch out, because “acid-free” does not mean “unbuffered”.

Is cyanotype dangerous?

The risk is low, but it is not zero and it is not “non-toxic”. Safety data sheets classify potassium ferricyanide as an eye irritant and as toxic to aquatic organisms, and its acute toxicity is low. With goggles, gloves, no acids anywhere near and the leftovers taken to a hazardous waste point, it is a process you can perfectly well handle at home.

Your next step

Prepare your piece: how to make a cyanotype step by stepHow to make a cyanotype at home: the solution, the paper, exposure in the sun or under a lamp, washing and drying, and a simple first session to get started.

Sources

  1. Ware, M. (n.d.). The traditional cyanotype process. Mike Ware: Alternative photography. https://mikeware.co.uk/mikeware/Traditional_Cyanotype.html Accessed October 16, 2026.
  2. Herschel, J. F. W. (1842). On the action of the rays of the solar spectrum on vegetable colours, and on some new photographic processes. Philosophical Transactions of the Royal Society of London, 132, 181-214. https://doi.org/10.1098/rstl.1842.0013
  3. Turner, J., Parisi, A. V., Downs, N. and Lynch, M. (2014). From ultraviolet to Prussian blue: A spectral response for the cyanotype process and a safe educational activity to explain UV exposure for all ages. Photochemical & Photobiological Sciences, 13(12), 1753-1764. https://doi.org/10.1039/c4pp00166d
  4. Jacquard Products. (2015). Cyanotype tips and troubleshooting [Manufacturer document, version 6.01.15]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Tips_and_Troubleshooting.pdf Accessed October 16, 2026.
  5. Jacquard Products. (2021). Cyanotype detailed instructions [Manufacturer instructions, version 08.17.21]. https://cdn.shopify.com/s/files/1/0053/5540/5423/files/Cyanotype_Instructions.pdf Accessed October 16, 2026.
  6. Rupert, Gibbon & Spider, Inc. (2018). Safety data sheet: Ferric ammonium citrate (CHM1102, CHM2102, JCY1100). https://uwaterloo.ca/fine-arts/sites/default/files/uploads/documents/ferric-ammonium-citrate_2018-02-07.pdf. Accessed October 16, 2026.
  7. Honeywell Specialty Chemicals Seelze GmbH. (2025). Safety data sheet: Potassium hexacyanoferrate(III) (version 2.4, ref. 31253). https://pdf.dutscher.com/doc/31253-1KG-HON/31253-1KG-HON_FDSen.pdf. Accessed October 16, 2026.

Checked on November 5, 2026. If you spot an error or a missing source, write to us.